LED PAR 64 SLIM 7x0W RGBW - PS0710

LASER 1000mW 3D
RGB SD CARD
F4000217
USER MANUAL / INSTRUKCJA OBSŁUGI
LASER 1000mW 3D RGB SD CARD F4000217
Table of contents
1
Introduction ......................................................................................................................................................... 2
2
Safety information .............................................................................................................................................. 2
3
Installation ........................................................................................................................................................... 3
4
Connections ......................................................................................................................................................... 3
4.1
Connecting DMX signal ............................................................................................................................... 3
4.2
Voltage specification ..................................................................................................................................... 3
4.3
Connecting power supply ........................................................................................................................... 4
5
Operation manual ............................................................................................................................................... 4
5.1
Control panel ................................................................................................................................................. 4
5.2
SD Card ........................................................................................................................................................... 4
5.3
DMX channel list ........................................................................................................................................... 5
1
www.flash-butrym.pl
1
INTRODUCTION
Thank you for purchasing LASER 1000mW 3D RGB SD CARD. For safety reasons and to ensure the troublefree operation, carefully read the instructions.
2
SAFETY INFORMATION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Installation should be done by qualified personnel in order to minimize the risk of accidental
electric shock
Disconnect the power supply before installation.
Before connecting the unit to the mains, make sure it is not damaged mechanically. If you
notice any signs of damage you should contact your dealer immediately. Do not connect the
device to the mains.
Do not use the device in high humidity conditions and at temperatures above 40° C
The device must be installed on stable structures
The unit must be well protected against moisture, dust and shaking. Do not use the
product in dusty environment.
The distance between lighting and illuminated object should be greater than 1 meter.
Ensure the fan is not blocked.
Do not look into the laser source.
Do not turn the device on and off frequently.
Please turn the unit off for 15 minutes after two hours of operation. Ensure that the laser
system is properly cooled.
Do not touch the laser lighting with wet hands and do not pull the power line.
Prevent the laser light from strong vibration.
In case of any problems please contact your distributor.
Be sure that the power supply parameters is matched with the parameters marked on the
device.
Installation should be made by professional technician.
Be sure that there is no flammable or explosive subject nearby.
The distance from the light source and other object should be at least 0,5m (at least 15cm
from walls).
Please check whether the fan and the ventilation holes are not blocked.
If the device is suspended, make sure that the security cable is able to lift at least ten times
its weight.
For security reasons it is important to properly ground the unit.
Warning! When installing the device make sure that it is mounted in a way that prevents the people from
the audience to look directly into the light. This carries the risk of eye damage.
Avoid contact with eyes. Never look at the laser equipment or directly in the laser beam.
Provisions concerning the use of the laser may vary depending on the country. User is legally responsible
for the use of the device depending on location / country.
www.flash-butrym.pl
2
LASER 1000mW 3D RGB SD CARD F4000217
3
INSTALLATION
After removing the packaging, check if the device was not damaged during transport. Before connecting to
the mains, make sure that the device is securely mounted. The manufacturer is not responsible for damage
caused by unstable mounting.
Ensure proper connection to the mains and proper grounding. Make sure that the electrical parameters are
consistent with device requirements. All activities, including connecting the device to the mains must be
performed by qualified personnel.
4
CONNECTIONS
The device is equipped with the following interfaces:
1.
2.
4.1
DMX (in/out): XLR 3-pin socket
Power (in): integrated power cord
Connecting DMX signal
The connection is performed using cable with XLR-female -> XLR-Male plugs.
GROUND
1
1
DMX +
3
3
DMX -
2
2
FEMALE
XLR
MALE
XLR
DMX 512
DMX 512
DMX Controller
4.2
Voltage specification
3
Input Voltage
Total Power
Frequency
100~240V
40W
50/60Hz
www.flash-butrym.pl
4.3
Connecting power supply
The connection is performed using integrated power cable with Unischuko power plug.
The device must be operated by qualified personnel. Make sure that the power grid supply parameters are
consistent with device parameters and limitations are not exceeded.
CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only
on the manufacturer or by a person with appropriate permissions.
5
OPERATION MANUAL
5.1
Control panel
The control panel is equipped with display and 4 control buttons:
1.
2.
3.
4.
5.2
MENU
DOWN
UP
ENTER
SD Card
1.
2.
3.
4.
The device supports the FAT32 file system. If you are using a new SD card, it must be formatted
in FAT32.
The maximum files and folders names length can be up to 8 characters (not including the
extension).
The device supports up to 100 folders. Each folder can store up to 255 files.
User can edit or create the Program List (*.prg file) using a text editor. Program List file contains a
list of Effect Files (*.ild) that will be played in a specified sequence. It also contains information
about play speed and the amount of repetition of each effect. Each line corresponds to one effect
file. Values are separated by commas.
Example of Program List file content, composed by three effect files: file1.ild, file2.ild and file3.ild:
File1.ild,12,3
File2.iid,20,1
File3.ild,18,4
In this example first effect will be played three times at a speed of 12, next effect will be played one time at
a speed of 20 and the last effect will be played four times at a speed of 18.
To work properly all files must be placed in one folder named the same as Program List file (*.prg)
Device supports standard ILDA (*.ild) files that can be downloaded or created using dedicated ILDA editor.
www.flash-butrym.pl
4
LASER 1000mW 3D RGB SD CARD F4000217
5.3
DMX channel list
13CH mode
5
Channel
Function
CH 1
Mode select
CH 2
Graphic select (Manual mode)
Folder select (PRG/ILD mode)
CH 3
Strobe (Manual mode)
File select (PRG/ILD mode)
CH 4
X-axis move
CH 5
Y-axis move
CH 6
Zoom
CH 7
X-axis rotate
CH 8
Y-axis rotate
CH 9
Center rotate
CH 10
Drawing
Effect
000-073: Off
074-110: Program (PRG)
111-147: Single effect (ILD)
148-184: Sound
185-221: Auto
222-255: Manual
Manual mode (CH 1 selection):
000-255: Select built-in graphic
PRG/ILD mode (CH 1 selection):
000-255: Select SD Card folder
Manual mode (CH 1 selection):
000-010: Strobe off
011-199: Strobe slow to fast
200-255: Strobe – sound activated
PRG/ILD mode (CH 1 selection):
000-255: Select file in folder selected in CH 2
000-125: Manually set X position
126-185: Auto left-right move
186-225: Auto right-left move
225-245: Auto random position jump
246-255: Sound activated random position jump
000-125: Manually set Y position
126-185: Auto up-down move
186-225: Auto down-up move
225-245: Auto random position jump
246-255: Sound activated random position jump
000-010: No function
011-100: Manually set size
101-150: Auto zoom-in
151-200: Auto zoom-out
201-255: Auto zoom cycle
000-010: No rotation
011-110: Manually set angle
111-255 Auto rotating
000-010: No rotation
011-110: Manually set angle
111-255 Auto rotating
000: No rotation
001-180: Manually set angle
181-217: Auto clockwise rotation
218-255: Auto counterclockwise rotation
000-010: No function
011-074: Manually draw
075-104: Auto draw – add
105-144: Auto draw - subtract
145-184: Auto cycle draw
185-224: Auto draw - subtract
www.flash-butrym.pl
CH 11
Waving
CH 12
Color change
CH 13
Display mode
www.flash-butrym.pl
000-010: No function
011-199: Small wave – slow to fast
200-255: Large wave – slow to fast
000-027: White
028-196: Various colors
170-220: Various color change
221-237: Different colors for each element of
displayed picture
238-255: Color change – sound activated
000-063: Standard
064-127: Highlights
128-191: Bars
192-255: Points
6