loxone nano dimmer air

Aptom System Sp. z o.o.
ul. Przy Bażantarni 11
02-793 Warszawa
tel. + 48 22 649 95 84
faks. +48 22 649 61 00
e-mail: [email protected]
LOXONE NANO
DIMMER AIR
COMISSIONING
Here we see how the Loxone Nano Dimmer Air can be learnt in, it must first be placed in
Learn Mode.
Initial Startup:
When the Nano Dimmer Air is first powered up it will automatically start in Learn Mode.
Restarting Learn Mode:
If you ever need to put a Loxone Nano Dimmer Air back into learn mode this can be done
very easily. Simply press and hold the learn button for 5 seconds within 10 seconds of
powering the device up. This will force the Dimmer Air back into Learn Mode
The learn button is located on the front bottom left of the unit (see below).
Once the unit is in the learn mode, the status LEDs will alternately blink Red - Green Yellow.
Now we have to start the air search. To do this, select the Air Base Extension in the Periphery
Tree, and then click the button "Air Device Search".
Aptom System Sp. z o.o.
NIP: 951-235-33-09
REGON: 145995134
KRS: 0000410057
Bank PEKAO VII o. w Warszawie
83 1240 1109 1111 0010 4473 3613
Aptom System Sp. z o.o.
ul. Przy Bażantarni 11
02-793 Warszawa
tel. + 48 22 649 95 84
faks. +48 22 649 61 00
e-mail: [email protected]
In the learn monitor all Air devices that are in learn mode will be displayed.
Now select the device you wish to add to your configuration. Enter the item name, select a
room from the drop-down and finally click "Create Device".
The Nano Dimmer Air will now be listed in the Periphery Tree.
As default only the output will be listed here. Additional diagnostic inputs like Online Status
and CPU Temperature can be added by checking the "Display Diagnostic Inputs" in the
Properties.
The "Dimming Type" is by default set to "Off".
When comissioning the correct dimming type must be selected for the load being connected.
REPLACING THE NANO DIMMER AIR
If you need to replace a device in Loxone Config, this can easily be done through the Air
Monitor.
•
•
Install and power up the Nano Dimmer Air and place the device in learn mode. (see
Commissioning )
Highlight the device in the Air Monitor when it appears.
Aptom System Sp. z o.o.
NIP: 951-235-33-09
REGON: 145995134
KRS: 0000410057
Bank PEKAO VII o. w Warszawie
83 1240 1109 1111 0010 4473 3613
Aptom System Sp. z o.o.
ul. Przy Bażantarni 11
02-793 Warszawa
•
tel. + 48 22 649 95 84
faks. +48 22 649 61 00
e-mail: [email protected]
Using the drop-down menu select the device to be replaced and click the "Replace device "
button.
Once this is done, save the configuration to the Miniserver.
LOXONE TOUCH FOR NANO
For the Nano Dimmer Air there is the Loxone
Loxone Touch and Touch Pure for Nano. These
provide Loxone touch capability to the Nano
Dimmer by piggybacking off the Air Technology
within the device.
If you are using the Loxone Touch for Nano, you need to
select this in the properties of the Nano Dimmer Air.
The touch points may be used in the Loxone Config as
individual digital inputs, these can be added to the periphery
via the properties of the touch.
Aptom System Sp. z o.o.
NIP: 951-235-33-09
REGON: 145995134
KRS: 0000410057
Bank PEKAO VII o. w Warszawie
83 1240 1109 1111 0010 4473 3613
Aptom System Sp. z o.o.
ul. Przy Bażantarni 11
02-793 Warszawa
tel. + 48 22 649 95 84
faks. +48 22 649 61 00
e-mail: [email protected]
LONG CLICK
To use long-clicks, the "Recieve Timeout" property must be set to 0 (not used) or a
correspondingly large value must be set in the properties of the device in (higher than
maximum click duration) . This value can be set separately in the properties for each digital
input of the device.
CABLING
Please note that the Nanon Dimmer Air only has a single output channel, but two terminals
for connections.
The Nano Dimmer Air is not suitable for low voltage or DC applications, but only 230V AC.
The terminals are rated for currents of up to 10A for looping cables in and out, but the dimmer
channel is NOT. To avoid damage observe the maximum allowed load stated in the
specifications at the top of this page.
TECHNICAL DATA
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Power supply: 230V AC, 50 / 60Hz (Terminals Reated at Max 10A)
Single dimmed output. Leading or trailing edge selectablein software
For traditional loads (incandescent bulbs, coil transformers) max. 200W i.e. 200VA min. 30W
For capacitive loads (LEDs, electronic transformers) max. 110W i.e. 110VA - min.
15W i.e. 15VA
Based on Loxone Air Technology
Frequency: 868 MHz (SRD band Europe), 915MHz (ISM Band Region 2)
Standby Power Consumption: 0.4 W approx
Dimensions: 53 x 53 x 31mm
Onboard microprocessor
Ambient temperature: 0 - 35 °
Max. Relative humidity 95% (non-condensing)
Protection: IP20
Method of Type 1 (EN60730-1)
Rated surge voltage: 1kV (EN60730-1, max altitude 2000m.)
Aptom System Sp. z o.o.
NIP: 951-235-33-09
REGON: 145995134
KRS: 0000410057
Bank PEKAO VII o. w Warszawie
83 1240 1109 1111 0010 4473 3613