Technical Instructions Supplies Tools 1
Transkrypt
Technical Instructions Supplies Tools 1
HP2400TECH Technical Instructions CORPORATE LOS ANGELES, USA US 1 800 394.9900 Int’l +1 818 837.8100 FAX 1 800 394.9910 Int’l +1 818 838.7047 Toner Drum Wiper Blade Lint-Free Cloth Supplies Tools Cotton Swab Anhydrous Isopropyl Alcohol Mag Roller Cleaner ATLANTA, USA US 1 877 676.4223 Int’l +1 770 516.9488 FAX 1 877 337.7976 Int’l +1 770 516.7794 Photo 1 Step 1 DALLAS, USA Place the cartridge on the workbench so the drum faces up. Using a small driftpunch and a hammer, carefully tap the cartridge pins into the waste hopper. (See Photos 1 & 2) US 1 877 499.4989 Int’l +1 972 840.4989 FAX 1 877 774.1750 Int’l +1 972 840.1750 MIAMI, USA US 1 800 595.429 Int’l +1 305 594.3396 FAX 1 800 522.8640 Int’l +1 305 594.3309 NEW YORK, USA Philips Screw Driver Small Flat Blade Screw Driver Needlenose Pliers Diagonal Cutters Drill 3/32 Drill Bit Drift Punch Hammer Photo 2 US 1 800 431.7884 Int’l +1 631 345.0121 FAX 1 800 431.8812 Int’l +1 631345.0690 SANFORD,USA US 1 800 786.9049 Int’l +1 919 775.4584 FAX 1 800 786.9049 Int’l +1 919 775.4584 TORONTO, CAN CAN 1 877 848.0818 Int’l +1 905 712.9501 FAX 1 877 772.6773 Int’l +1 905 712.9502 Photo 3 Step 2 BUENOS AIRES, ARG Separate the two sections of the cartridge. (See Photo 3) ARG 0810 444.2656 Int’l +011 4583.5900 FAX +011 4584.3100 MELBOURNE, AUS AUS 1 800 003. 100 Int’l +62 03 9561.8102 FAX 1 800 004.302 Int’l +62 03 9561-7751 SYDNEY, AUS AUS 1 800 003.100 Int’l +62 02 9648.2630 FAX 1800 004.302 Int’l +62 02 9548.2635 Photo 4 MONTEVIDEO,URY URY 02 902.7206 Int’l +5982 900.8358 FAX +5982 908.3816 JOHANNESBURG, S.A. S.A. +27 11 974.6155 FAX +27 11 974.3593 E-mail: [email protected] Step 3 Using a pair of pliers, grab a hold of the contact protector arm that the drum axle fits in, located on the contact side of the waste hopper. Pull the drum axle pin out from the end of the waste hopper. (See Photo 4) NOTE: Do not lose the tension spring that sits behind the protector arm. Website: www.futuregraphicsllc.com 1 2 HP 2400 Technical Instructions Photo 5 Step 4 Remove the drum axle pin from the contact protector arm. Reattach the tension spring to the contact protector arm. (See Photos 5) Notes Photo 6 Step 5 Lift up on the non gear side of the drum, removing the drum from the bearing hub. (See Photos 6) Photo 7 Step 6 Lift out the PCR. (See Photos 7) Clean the PCR using a mild soap and water. Photo 8 Step 7 Remove the two screws holding the wiper blade and remove the blade. (See Photo 8) Dump out the waste toner and clean the hopper using dry compressed air or a vacuum. Photo 9 Step 8 Apply padding powder to the wiper blade. Place the blade into the hopper and install the two screws that hold the blade in place. (See Photo 9) Need trust-worthy, detailed Technical Instructions for another engine? Visit: www.futuregraphicsllc.com HP 2400 Technical Instructions 3 Photo 10 Step 9 Clean the PCR saddles using a cotton swab and alcohol. Apply new conductive grease to the black conductive saddle. (See Photo 10) Photo 11 Step 10 Place the PCR into the waste hopper. (See Photo 11) Photo 12 Photo 15 Step 14 Remove the shutter arm from the alignment post. Do not lose the tension spring that sits behind the arm. Place the tension spring back into the drum shutter arm. (See Photo 16) Step 12 Place the drum axle pin into the contact protector arm. Slide the drum axle into the end of the waste hopper. (See Photo 13) Photo 14 Release the locking tab that holds the drum shutter arm to the toner hopper. (See Photo 15) Step 11 Apply padding powder to the drum. Carefully slide the drum onto the contact axle while rotating the drum counterclockwise. (See Photo 12) Photo 13 Step 13 Photo 16 NOTE: The tension spring for the protector arm fits into a notch in the waste hopper located at about 11 o’clock (when looking at the end of the drum axle). (See Photo 14) Open the protector arm to engage the tension spring. Need trust-worthy, detailed Technical Instructions for another engine? Visit: www.futuregraphicsllc.com 4 HP 2400 Technical Instructions Photo 19 Step 17 Remove the two screws holding the toner hopper gear housing end cap. (See Photo 19) Slide the gear housing end cap away from the toner hopper. Step 15 Remove the drum shutter bar from the contact side of the toner hopper. (See Photo 17) Step 18 Photo 17 Photo 20 Remove the two screws holding the contact end cap to the toner hopper. (See Photo 20) Remove the end cap. Step 19 Lift the mag roller away from the toner hopper. (See Photo 21) Step 20 Photo 21 Step 16 Remove the mag roller stabilizer bar and the mag roller bushings from the ends of the mag roller. Clean the mag roller fist using dry compressed air or a vacuum, and then by using a mag roller cleaner. Remove the drum shutter bar from the gear housing end cap. (See Photo 18) Step 21 Remove the two screws holding the doctor blade. (See Photo 22) Photo 18 Photo 22 Step 22 Remove the plastic scrapers from the end of the doctor blade. Lift out the doctor blade. (See Photo 23) Clean the doctor blade using a lint-free cloth and alcohol. Photo 23 Step 23 Dump the unused toner from the toner hopper. Clean the toner hopper using dry compressed air or a vacuum. Step 24 Fill the toner hopper through the mag roller opening. Need trust-worthy, detailed Technical Instructions for another engine? Visit: www.futuregraphicsllc.com E-mail: [email protected] Website: www.futuregraphicsllc.com HP 2400 Technical Instructions Photo 24 5 Step 25 Place the cleaned doctor blade onto the toner hopper. Install the two plastic scrapers on each side of the blade and install the two screws that hold the doctor blade in place. (See Photo 24) Step 26 Photo 25 Photo 26 Slide the black mag roller bushing onto the contact side of the mag roller, and the green bushing onto the drive gear side of the roller. Install the stabilizing bar onto the mag roller with the C-bearing facing towards the mag roller bushing. Slide the mag roller drive gear onto the roller so the injection molding points face outward. (See Photo 25) Photo 29 Photo 30 Step 28 Place the contact end cap onto the end of the toner hopper. Install the two screws that hold the end cap in place. (See Photo 27) NOTE: Make sure the white bearing is present in the contact end cap before it is installed. Photo 28 Insert the non-keyed end of the drum shutter bar into the positioning hole on the contact side of the toner hopper. (See Photo 29) Press the keyed end of the drum shutter bar into the gear housing end cap. (See Photo 30) Step 27 Place the mag roller into the toner hopper. (See Photo 26) Photo 27 Step 30 Step 29 Place the gear housing end cap onto the end of the cartridge. Install the two screws that hold the end cap in place. (See Photo 28) Step 31 Slide the drum shutter arm onto the positioning post. Install the drum shutter arm into the drum shutter. Slide the drum shutter open to engage the tension spring. (See Photo 30) Photo 31 6 HP 2400 Technical Instructions Photo 32 Photo 31 Step 32 Holding the drum shutter open, join the toner hopper and waste hopper. Install the cartridge pins in each end of the cartridge. (See Photos 31 & 32) First Look into the New HP LaserJet 2400 The new HP LaserJet 2400 series of printers consists of three models, the LaserJet 2410, the LaserJet 2420 and the LaserJet 2430. The LaserJet 2410 prints at 25ppm and will only be sold into Europe and Latin America. The LaserJet 2420 printer series is made up of four models capable of printing 30 pages per minute at up to 1200 x 1200 dpi with HP ProRes 1200, Resolution Enhancement technology (REt). The base model 2420 will sell for $549. The LaserJet 2420d comes with duplex capabilities, 48MB of RAM standard and sells for $649; the network version the LaserJet 2420n lists at $799 and the LaserJet 2420dn sells for $899 it has duplex capabilities and is network ready. The HP LaserJet 2430 series of printers is available in three models. Each printer ships with an additional 500 sheet paper tray and all three models are network ready. The printers print up to 35ppm at up to 1200 x 1200 dpi with HP ProRes 1200 and Resolution Enhancement technology (Ret). The HP LaserJet 2430t will not be available in the U.S. do to the fact that HP feels that at 35ppm the LaserJet 2430 will be used in a networking environment. The LaserJet 2430tn is network ready and sells for $999, while the HP2430dtn lists at $1099, is network ready, and is able to duplex. Machines: HP HP HP HP HP LaserJet LaserJet LaserJet LaserJet LaserJet 2410 2420 2420d 2420n 2420dn The toner cartridges for the HP2400 series are available in a 6,000 page standard yield (Q6511A) and a 12,000 page high yield (Q6511X) cartridge. The high yield cartridge sells for $205.99 which at 5% coverage would give you a cost of 2 cents per page, while at $123.99, the low yield cartridge would cost you 1.7 cents per page. OEM Information: HP LaserJet 2430t HP LaserJet 2430tn HP LaserJet 2430dtn Q6511A – 6,000 pages at 5% coverage Q6511X – 12,000 pages at 5% coverage Future Graphics (FG) is a distributor of compatible replacement parts and products for imagining equipment. None of FG's products are genuine OEM replacement parts and no affiliation or sponsorship is to be implied between FG and any OEM.