delphi chassis systems
Transkrypt
delphi chassis systems
NEXTEER SUPPLY MANAGEMENT Nexteer Automotive Poland Sp. z o.o. Ul.Towarowa 6 43-100 Tychy Poland REQUEST FOR QUOTATION # 0730 Date: 31.08.2016 Contact Person: Piotr Muziol e-mail: [email protected] Phone: +48 724 950 750 Delivery: DDP Nexteer Tychy, Poland, Terms: MNS2.2 – 2nd day 2nd month 100% MNS2.2 – after MQ2 acceptance at Supplier floor Please register your company account on site https://nexteerdataexchange.com/. The account is free and necessary for communication between the Supplier and Nexteer especially as regards the secure transmission of documents, drawings, etc. Please inform about your contact person on portal. Instructions: 1. Your bid must be submitted electronically no later than 7th of September 2016, 11:00 (Central Europe Time). E-mail your quote to the attention of: [email protected] 2. We reserve the right to reject any and all quotations. Quotations received after the bid closing date are subject to rejection, and will be returned unopened. Timing respond is condition under which quotation will be taken into consideration in quoting process . 3. All proposals for this RFQ must be addressed to and delivered only to the Buyer’s noted above. 4. Buyer "Purchase order terms and conditions” apply. Exceptions should be submitted in detail with your proposal. Supplier acknowledges and agrees that Buyer’s General Terms and Conditions and Customer Specific Requirements are incorporated in, and a part of, this Request for Quote. By responding to this Request for Quote or commencing any work, services or other activities related to this Request for Quote, Supplier acknowledges and agrees that Buyer’s General Terms and Conditions and Customer Specific Requirements will apply to any resulting contract between Buyer and Supplier (including any purchase order, release, requisition, work order, shipping instruction, specification and other document issued by Buyer or accepted in writing by Buyer) in their entirety without modification. A copy of Buyer’s General Terms and Conditions and Customer Specific Requirements are available upon written request to Buyer or via the internet at Buyer’s website: http://www.nexteer.com/wpcontent/uploads/2016/05/ME-TCs-Eff-June-1-2016-clean-final1.pdf / http://www.nexteer.com/doing-business-withnexteer/ Supplier acknowledges and agrees that it has read and understands Buyer’s General Terms and Conditions. Any additions to, changes in, modifications of, or revisions of Buyer’s General Terms and Conditions which Supplier proposes in any Quote or other document or communication will be deemed to be rejected by Buyer except to the extent that Buyer expressly agrees to accept any such proposals in writing. 5. Specifications and drawings are property of Neexter Automotive Poland Sp. z o.o.. and can not be use to any supplier purposes and pass to any third party. 6. All correspondence containing changes to the shipping schedule or the project price must be addressed to and delivered only to the Buyer noted above. 7. Buyer will not be responsible for the cost of any material, labor or services expect as authorized in advance by a written purchase order alternation from the Global Supply Management (purchasing document). 8. Late delivery penalty per paragraph 2.7 of Buyer’s Machinery and Equipment Terms and Conditions. Additional costs incurred by the supplier to achieve agreed-upon shipment date are the supplier’s responsibility and will not be reimbursed by Buyer. Please quote the following: The measuring arm (7 axis) with software and accessories for measurements: • squareness • alignment • parallelism • flatness • concentricity • measurement basis points REQUIREMENTS - Calibration in the laboratory meets the ISO 17025: 2006 - Wireless Bluetooth, WI-FI and wired USB, LAN -Sensors at the joints, warning of overload in the arm, which may affect the accuracy of measurement. - The range of the arm is not less than 2.6 m diameter sphere working The accuracy of the single point test -max 0.029 mm The accuracy of the volume test - 0.041 mm max Power cable USB cable Battery Suitcase Accessories: 1 x 3 mm nozzle tip and 1 x 6mm A metal mounting foot Cone calibration probes LCD screen for simple measurements without the use of computers. Ramie pomiarowe 7 osi z oprogramowaniem oraz akcesoriami do pomiarów: prostopadłość osiowość równoległość płaskość współśrodkowość pomiar punktów bazowych WYMAGANIA - kalibracja i wzorcowanie urządzeń w laboratorium spełniającym normę ISO 17025:2006 - komunikacja bezprzewodowa Bluetooth, WI-FI oraz przewodowa USB, LAN -Czujniki naprężeń w przegubach ostrzegające o przeciążeniach w ramieniu, które mogą wpływać na dokładność pomiaru. - Zasięg ramienia nie mniejszy niż 2,6m średnicy sfery roboczej Dokładność w teście pojedynczego punktu –max 0,029 mm Dokładność w teście objętościowym – max 0,041 mm Kabel zasilający Kabel USB Bateria Walizka Akcesoria: 1 x końcówka 3mm oraz 1 x końcówka 6mm Metalowa stopa montażowa Stożek do kalibracji sond Ekran ciekłokrystaliczny umożliwiający proste pomiary bez użycia komputery Gwarancja minimum 24 miesiące Specyfikacja ramienia - wyposażone w kompensacje termiczną - równa długość członów ramienia Wmontowany system przeciwwag w urządzeniu Przewody łączące skaner wmontowane w urządzenie Niezbędne oprogramowanie (licencja na 1 stanowisko) – wraz ze wsparciem serwisowym minimum przez rok. Stopa magnetyczna do ramienia ( opcja) Statyw do ramienia (opcja) Zestaw przedłużek do sond pomiarowych (opcja) Dostawa DAP Nexteer Tychy A. All questions on commercial issue must be addressed to the Buyer - Piotr Muzioł: [email protected] – mobile: +48 724 950 750 Technical questions can be directed to responsible engineer – Michał Pytlok: [email protected], mobile: +48 797-005-855 B. Please quote your best delivery date in weeks after receipt of Purchase Order (ARO) C. All quotations must show a two years warranty. D. Criteria of the offer selection: Supplier who will receive our order should be the best in total in following aspects (Supplier can achieve maximum 100%) Price – 80% - it will be calculated 0,8 x(the best offered price/price offered by supplier in evaluated offer) Delivery date - 20% - it will be calculated 0,2 x(the best offered delivery date/delivery date in evaluated offer) Compliance to this RFQ letter: Please sign and date below to confirm compliance to the requirements to this document. Return the signed document to the Buyer with your proposal. Name: Signature: Data: Company: We welcome non-confidential suggestions regarding changes in specification and/or modifications in design production methods which will aid in reducing costs, without impairing quality, or which will improve the quality and/or performance of the product on which you are quoting.