Please use cable D35. Tachographs with power supply

Please use cable D35. Tachographs with power supply

Please use cable D35.
Tachographs with power supply of 12V or 24V can be programmed
with DiagProg 3.
ElproSys Sp. z o.o. ® Elektronika samochodowa, oprogramowanie, chip tuning.
44-100 Gliwice, ul.Tarnogórska 140 tel. (32) 301-2-301, fax. (32) 301-2-302
POWER SUPPLY:
First method
Tachograph is mounted in the car and powered by original plug (no dismounting)
CABLE D35
Tachograph powered by car
DiagProg 3 must be pewered by external power supply
!!! CAUTION !!!
DIAGPROG 3 IS SUPPLIED WITH 12V ONLY
Second method
Tachograph powered by cable D35 bundle of power wires – after dismounting tachograph
from the car
Tachograph powered by cable D35 bundle of power wires
CABLE D35
– after dismounting tachograph from the car
DiagProg 3 must be pewered by external power supply
!!! CAUTION !!!
DIAGPROG 3 IS SUPPLIED WITH 12V ONLY
ElproSys Sp. z o.o. ® Elektronika samochodowa, oprogramowanie, chip tuning.
44-100 Gliwice, ul.Tarnogórska 140 tel. (32) 301-2-301, fax. (32) 301-2-302
STONERIDGE ELECTRONICS VEEDER-ROOT 2400
PARAMETERS – POSSIBLE CORRECTIONS
PAGE 1
1.K factor
2.Odometer
3.Pulse per rev.
4.Idle RPM
5.Economy RPM
6.Poor Econ. RPM
7.CANBus RPM
8.RPM Display
9.Dist Display
PAGE 2
1.DTCs Display
2.Overspeed Flash
3.Overspeed
4.Time & Date
5.O/P Shaft
6.4th Chart Tr
7.CANBus Enable
8.CAN Type
9.Dual Axle
PAGE 3
1.D.Axle Ratio
2.D6 pin funct.
3.Speedo.OP factor
4.Serial Comms
5.Ignit.On rec.
6.Driver 2 Duty
7.Reset HeartBt
8.Eject pin code
9.Sensor Type
PAGE 4
1.Service Delay
2.Installat.date
3.Calibration date
4.Repair Shop ID
5.Vehicle ID
ElproSys Sp. z o.o. ® Elektronika samochodowa, oprogramowanie, chip tuning.
44-100 Gliwice, ul.Tarnogórska 140 tel. (32) 301-2-301, fax. (32) 301-2-302
CABLE D35
POWER CONNECTOR
(CONNECTOR A)
ElproSys Sp. z o.o. ® Elektronika samochodowa, oprogramowanie, chip tuning.
44-100 Gliwice, ul.Tarnogórska 140 tel. (32) 301-2-301, fax. (32) 301-2-302
KIENZLE / VDO MTCO 1324, MTCO 1390
PARAMETERS – POSSIBLE CORRECTIONS
PAGE 1
1.K Factor
2.Odometer
3.Instal. Date
4.Calibr. Date
5.Time & Date
6.O/P Shaft
7.Service Delay
8.CAN priority
9.Binary Code
PAGE 2
1.Product Code
2.VIN
3.N-RPM Factor
4.L_Tyre
5.Serial Number
CABLE D35
POWER CONNECTOR
(CONNECTOR A)
ElproSys Sp. z o.o. ® Elektronika samochodowa, oprogramowanie, chip tuning.
44-100 Gliwice, ul.Tarnogórska 140 tel. (32) 301-2-301, fax. (32) 301-2-302
In order to program lower value of kilometer counter in model MTCO 1324, you need to reset
the tachograph by following procedure below.
Before reseting the tachograph it is strongly recommended to read and write all original
parameters!!!
LEGAL DISCLAIMER
It is forbidden to use DiagProg3 device, software for this device, information contained in this document and any other Elprosys products for purposes which are
illegal or prohibited in any other way. Elprosys and the company’s management board shall not be liable for the results of the use of the DiagProg3 device, soft ware, information contained in this document and any other Elprosys products for purposes which are illegal or prohibited in any other way. Copying, redistribu tion, publishing, dissemination, sale, giving access to or making use in any other way of the whole or part of the software and data contained in this document are
forbidden. Elprosys may introduce improvements or modifications of products on offer and their documentation as well instruction manuals at any time without a
prior notice. Any and all trademarks, product names and information set forth in the document are the property of the Elprosys company and are protected by the
law. A User is required to respect intellectual property rights of resources contained in the document.
ElproSys Sp. z o.o. ® Elektronika samochodowa, oprogramowanie, chip tuning.
44-100 Gliwice, ul.Tarnogórska 140 tel. (32) 301-2-301, fax. (32) 301-2-302
ElproSys Sp. z o.o. ® Elektronika samochodowa, oprogramowanie, chip tuning.
44-100 Gliwice, ul.Tarnogórska 140 tel. (32) 301-2-301, fax. (32) 301-2-302