LiFe BALANCE 5.5A 19.8V(6S)
Transkrypt
LiFe BALANCE 5.5A 19.8V(6S)
LiFe STORAGE 2.0A 19.8V(6S) LiFe DISCHARGE 2.0A 19.8V(6S) LiFe BALANCE LiIo 2.0A BALANCE 19.8V(6S) 2.0A 21.6V(6S) LiFe BALANCE NiMH CHARGE 2.0A 19.8V(6S) CURRENTLiFe CHARGE 2.0A LiIo 2.0A CHARGE 19.8V(6S) 2.0A 21.6V(6S) LiFe CHARGE NiMH Auto CHARGE Instruction Manual | Bedienungsanleitung | Manuel d’utilisation | Manuale di Istruzioni 2.0A 19.8V(6S) CURRENT 2.0A LiFe FAST FAST CHG CHG PROGRAM SELECT LiIo PROGRAMLiFe SELECT 2.0A 19.8V(6S) BATT 2.0A 21.6V(6S) LiIo BATT LiFe FAST CHG NiMH DISCHARGE PROGRAM SELECT PROGRAM SELECT • Never attempt to charge a battery pack containing different types of batteries. NOTICE Not to scale. Programming quick Guide 2.0A 19.8V(6S) 0.1A CUT:1.0V NiMH BATT LiFe BATT LiFe STORAGE • Never allow children under 14 years of age to charge battery packs. LiIo All instructions, warranties and other collateral documents are subject to change Not all wiring shown. Press the Mode key (G) to get to the 9 main menus from any submenu screen. 2.0A STORAGE 19.8V(6S) • Never charge batteries in extremely hot or cold places or place in direct sunlight. NiMH RE-PEAK 2.0A 21.6V(6S) LiFe STORAGE at the sole discretion of Horizon Hobby, Inc. For up-to-date product literature, visit Not all connectors shown. Press the Jog Dial (H) to get to the submenus2.0A for adjusting operating parameters, to save value changes or to start chosen battery charging actions.2 • Never charge a battery if the cable has been pinched or shorted. 19.8V(6S) LiFe DISCHARGE LiIo horizonhobby.com and click on the support tab for this product. Rotate the Jog Dial (H) to change between submenu screens or to change screen values. • Never connect the charger if the power cable has been pinched or shorted. 2.0A DISCHARGE 19.8V(6S) NiMH CYCLE 2.0A 21.6V(6S) LiFe DISCHARGE • Never connect the charger to an automobile 12V battery while the vehicle Meaning of Special Language DCHG>CHG 1 2.0A 19.8V(6S) NiMH CHARGE LiFe BALANCE LiIo is running. LiPo BALANCE BALANCE The following terms are used throughout the product literature to indicate various CURRENT 2.0A 2.0A 19.8V(6S) 2.0A 21.6V(6S) • Never attempt to dismantle the charger or use a damaged charger. 2.0A 22.2V(6S) LiIo BALANCE NiCd CHARGE levels of potential harm when operating this product: LITHIUM BATTEries (Li-Fe) Lithium Batteries (li-Ion) • Never attach your charger to both an AC and a DC power source at the same time. 2.0A 21.6V(6S) CURRENT 2.0A LiFe CHARGE NiMH Auto CHARGE LiIo CHARGE LiPo CHARGE NOTICE: Procedures, which if not properly followed, create a possibility of physical • Never connect the input jack (DC input) to AC power. 2.0A 19.8V(6S) CURRENT2.0A 2.0A 21.6V(6S) 2.0A 22.2V(6S) NiCd Auto CHARGE LiIo CHARGE property damage AND a little or no possibility of injury. • Always use only rechargeable batteries designed for use with this type of charger. CURRENT 2.0A 2.0A 21.6V(6S) LiFe FAST CHG NiMH DISCHARGE PROGRAM SELECT LiIo FAST CHG PROGRAM SELECT PROGRAM SELECT • Always inspect the battery before charging. LiPo FAST CHG PROGRAM SELECT CAUTION: Procedures, which if not properly followed, create the probability of NiMH CHARGE LiFe BALANCE 2.0A 19.8V(6S) 0.1A CUT:1.0V NiMH BATT 2.0A 21.6V(6S) LiIo BATT BATT LiFe BATT • Always keep the battery away from any material that could be affected by heat. PROGRAM SELECT 2.0A 22.2V(6S) NiCd DISCHARGE LiPo LiIo FAST CHG PROGRAM SELECT physical property damage AND a possibility of serious injury. 2.0A BALANCE 19.8V(6S) CURRENT 2.0A NiMH CHARGE LiFe 0.1A CUT:STORAGE 1.0V NiMH RE-PEAK 2.0A 21.6V(6S) LiIo BATT LiFe STORAGE • Always monitor the charging area and have a fire extinguisher available at all times. LiIo 2.0A 19.8V(6S) NiCd BATT CURRENT 2.0A LiPo STORAGE WARNING: Procedures, which if not properly followed, create the probability of 2 NiMH Auto CHARGE LiFe CHARGE 2.0A 19.8V(6S) 2.0A 21.6V(6S) • Always end the charging process if the battery becomes hot to the touch or starts 2.0A 22.2V(6S) NiCd RE-PEAK LiIo STORAGE 2.0A 19.8V(6S) CURRENT 2.0A property damage, collateral damage, and serious injury OR create a high probability NiMH Auto2 CHARGE LiFe CHARGE to change form (swell) during the charge process. NiMH CYCLE 2.0A 21.6V(6S) LiFe DISCHARGE LiIo DISCHARGE 2.0A 19.8V(6S) CURRENT 2.0A of superficial injury. LiPo DISCHARGE • Always connect the charge cable to the charger first, then connect the battery to DCHG>CHG 1 LiFe FAST CHG NiMH DISCHARGE PROGRAM SELECT 2.0A 19.8V(6S) 2.0A 21.6V(6S) PROGRAM SELECTLiIo 2.0A 22.2V(6S) NiCd CYCLE DISCHARGE avoid short circuit between the charge leads. Reverse the sequence when 2.0A FAST 19.8V(6S) 0.1A DISCHARGE CUT:1.0V BATT BATT LiFe CHG NiMH PROGRAMNiMH SELECT PROGRAMLiFe SELECT WARNING: Read the ENTIRE instruction manual to become familiar with the DCHG>CHG 1 2.0A 21.6V(6S) disconnecting. LiIo BALANCE NiCd CHARGE 2.0A 19.8V(6S) 0.1A CUT:1.0V NiMH BATT LiPo BALANCE LiFe BATT features of the product before operating. Failure to operate the product NiMH RE-PEAK LiFe STORAGE [BATT MEMORY 1] 2.0A 21.6V(6S) CURRENT2.0A ENTER 2.0A • Always connect the positive red leads (+) and negative black leads (–) correctly. 22.2V(6S) 2.0A 19.8V(6S) SET ->2 Pb CHARGE NiMH RE-PEAK correctly can result in damage to the product, personal property and cause LiPo BALANCE LiFe STORAGE • Always disconnect the battery after charging, and let the charger cool between 2.0A 2.0V (1P) 2 2.0A 22.2V(6S) NiCd Auto CHARGE LiIo CHARGE 2.0A 19.8V(6S) LiPo CHARGE serious injury. PROGRAM SELECT NiMH CYCLE TYPE LiFe DISCHARGE Lithium Batteries (Li-Po) charges. CURRENTBATT 2.0A 2.0A 21.6V(6S) 2.0A 22.2V(6S)1 Pb BATT DCHG>CHG This is a sophisticated hobby product. It must be operated with caution and common • Always charge in a well-ventilated area. LiPo 2.0A 19.8V(6S) NiMH CYCLE Pb DISCHARGE LiPo CHARGE LiFe DISCHARGE DCHG>CHG 1 PROGRAMPROGRAM SELECT SELECT2.0A 2.0VFAST (1P) CHG 2.0A 22.2V(6S) NiCd DISCHARGE LiIo FAST CHG 19.8V(6S) 2.0A PROGRAM SELECT LiPo sense and requires some basic mechanical ability. Failure to operate this Product • Always terminate all processes and contact Horizon Hobby if the product NiCd BATT LiIo BALANCE 0.1A BATT CUT:VOLTS 1.0V NiCd CHARGE 2.0A 21.6V(6S) LiIo BATT 2.0A 22.2V(6S) LiPo BATT in a safe and responsible manner could result in injury or damage to the product or malfunctions. 7.4V(2S) LiPo FAST CHG PROGRAM SELECT 2.0A 21.6V(6S) CURRENT 2.0A Battery Memory LiIo BALANCE NiCd CHARGE Rest other property. This product is not intended for use by children without direct adult 2.0A 22.2V(6S) NiCd Time RE-PEAK LiIo STORAGE LiPo BATT LiPo STORAGE WARNING: Never leave charger unattended, exceed maximum charge rate, 2.0A 21.6V(6S) CURRENT 2.0A CHG>DCHG 10min CHARGE CURRENT NiCd Auto LiIo CHARGE 2 CHARGE 2.0A 21.6V(6S) supervision. Do not attempt disassembly, use with incompatible components or 2.0A 22.2V(6S) charge with non-approved batteries or charge batteries in the wrong mode. 2.2A LiPo STORAGE CURRENT 2.0A 2.0A CHARGE 21.6V(6S) NiCd Auto CHARGE LiIo SAFETY TIMER augment product in any way without the approval of Horizon Hobby, Inc. This manual Failure to comply may result in excessive heat, fire and serious injury. 2.0A 22.2V(6S) NiCd CYCLE LiIo DISCHARGE LiPo DISCHARGE CURRENT 2.0A 2.0A 21.6V(6S) ON 120min PROGRAM SELECT DSCH CURRENT contains instructions for safety, operation and maintenance. It is essential to read PROGRAM SELECT NiCd DISCHARGE LiIo FAST CHG DCHG>CHG 1 21.6V(6S) PROGRAM SELECT2.0A 2.0A 22.2V(6S) BATT MEMORY LiPo DISCHARGE BATT 0.1A CUT: 1.0A 1.0V CAUTION: Always ensure the battery you are charging meets the 2.0A FAST 21.6V(6S) and follow all the instructions and warnings in the manual, prior to assembly, setup BATT PROGRAMNiCd SELECT NiCd DISCHARGE LiIo CHG Capacity Cut-Off PROGRAMLiIo SELECT 2.0A 22.2V(6S) NiCd BATT Pb CHARGE 0.1A CUT: 1] 1.0V specifications of this charger and that the charger settings are correct. Not 2.0A 21.6V(6S) LiPo BALANCE ON 5000mAh [BATT MEMORY LiIo BATT or use, in order to operate correctly and avoid damage or serious injury. DSCH VOLTAGE NiCd RE-PEAK LiIo STORAGE When Using an External AC Power Source: Getting Started 2.0A 2.0VENTER (1P) 2.0A 22.2V(6S) SET ->2 doing so can result in excessive heat and other related product malfunctions, 3.0V/CELL PROGRAM SELECT 2.0A 21.6V(6S) [BATT MEMORY 1] LiIo STORAGE Key BeepNiCd RE-PEAK ON 1. Connect the AC power cord to the charger AC power input port. Age Recommendation: Not for children under 14 years. This is not a toy. Pb BATT which can lead to user injury or property damage. Please contact Horizon CAUTION: Never connect the AC and DC input cords to an active power SET -> Pb DISCHARGE 2.0A 21.6V(6S) LiPo ENTER CHARGE Buzzer ONRISK! 2 BATT TYPE TVC=YOUR 2. Connect the AC power cord to the AC power source. NiCd CYCLE LiFe BALANCE NiMH CHARGE LiIo DISCHARGE Hobby or an authorized retailer with compatibility questions. Safety Precautions and Warnings source at the same time. This will void the warranty, cause product 2.0A 2.0V (1P) 4.20V1 2.0A 22.2V(6S) LiPo PROGRAM SELECT DCHG>CHG 2.0A 19.8V(6S) CURRENT 2.0A 2.0A 21.6V(6S) BATT TYPE 3. Power ON the charger with the power switch. NiCd CYCLE LiIo DISCHARGE Input Power Low damage and possibly injure the user. LiFe BALANCE Ni-Mh Batteries NiMH CHARGE WARNING: Failure to exercise caution while using this product and comply LiPo DCHG>CHG 1 2.0A 21.6V(6S)SYSTEM SET-> FAST CHG2.0A Cut-Off 11.0V SELECT BATT VOLTS TEMPERATURE 4. When the charger is powered ON, a message will appear on2.0A the LCDCHARGE screen. Rest Time NiMH Auto CHARGE LiFe 19.8V(6S) PROGRAMLiPo CURRENT Pb CHARGE LiPo BALANCE with the following warnings could result in product malfunction, electrical 2.0A 22.2V(6S) BATT 7.4V(2S) CUT-OFF 50C When Using an External DC Power Source: CHG>DCHG 10min CURRENT 2.0A 2.0A 19.8V(6S) BATT VOLTS Ext. Temp 0C C AUTION: Always power ON the charger before connecting a battery, or 2.0A 2.0V (1P) 2.0A 22.2V(6S) PROGRAM SELECT Pb CHARGE LiPo BALANCE issues, excessive heat, FIRE, and ultimately injury and property damage. CHARGE Auto CHARGE LiFe BALANCE NiMH CHARGE 1. Connect the DC power cord to the charger DC power input port. 7.4V(2S) LiPo DISCHARGE STORAGE Int. Temp 32C CHARGE CURRENT SAVE PROGRAM damage to the charger and the SELECT battery can result. 2.0A 2.0V (1P) 2.0A 22.2V(6S) PROGRAM SELECT SAFETY TIMER Pb BATT LiFe FAST CHG NiMH PROGRAM SELECT 2.0A 19.8V(6S) CURRENT 2.0A PROGRAM 2. Connect the DC alligator clips to the DC power source. Pb DISCHARGE LiPo CHARGE • Never leave the power supply, charger and battery unattended during use. 2.0A 22.2V(6S) 2.2A ENTER ON FACTORY 120min 2.0A 19.8V(6S) 0.1A CUT:1.0V NiMH BATT CHARGE CURRENT BATT Pb BATT LOAD SET 1. Connect the chargerPROGRAM to the power LiFe source. 2.0A 2.0V (1P) 2.0A 22.2V(6S) 3. Power ON the charger with the power switch. Pb DISCHARGE LiPo CHARGE • Never attempt to charge dead, damaged or wet battery packs. FAST CHG DISCHARGE PROGRAM SELECT LiFe CHARGE NiMH Auto CHARGE SELECT 2.2A PROGRAM SELECT LiPo RE-PEAK DISCHARGE DSCH CURRENT ENTER 2.0A 2.0V (1P) 2.0A 22.2V(6S) 2. Power ON the charger. Capacity Cut-Off LiFe STORAGE 0.1A CUT:1.0V 4. When the charger is powered ON, a message will appear on the LCD screen. NiMH BATT 2.0A 19.8V(6S) CURRENT 2.0A LiFe BATT BATT MEMORY LiPo FAST CHG 2.0A 22.2V(6S) PROGRAM SELECTNiMH 1.0A Rest Time • Short-circuit, over-current, reverse polarity, low input voltage and 2 ON 5000mAh PROGRAM SELECT 2.0A 19.8V(6S) DSCH CURRENT 3. Make program selections in the charger for battery charging. VERSION Included Items 2.0A 22.2V(6S) LiPo BATT NOTICE: Always connect cable polarities correctly. LiPo FAST CHG PROGRAM SELECT RE-PEAK STORAGE LiFe FAST CHG NiMH DISCHARGE PROGRAM SELECT SELECT CHG>DCHG 10min BATT MEMORY Rest Time 1.0A over-temperature protection 1.00 DSCH VOLTAGE 4. Connect the chargerPROGRAM adapters to the charger. [BATTCYCLE MEMORY 1] 22.2V(6S) 2.0A NiMH Key Beep ON 10min LiPo BATT 2 LiFe DISCHARGE 2.0A 19.8V(6S) 0.1A CUT:1.0V NiMH BATT LiFe BATT CHG>DCHG NOTICE: Always consult 12V battery collateral materials or Horizon Hobby JST_XH Balance adapter (2) LiPo STORAGE 3.0V/CELL • Storage and Fast Charge modes ENTER SET -> 5. Connect the battery to the charger adapters (connect main 2.0A charging TIMER DCHG>CHG 1 Buzzer SAFETY ON 19.8V(6S) DSCH VOLTAGE 2.0A 22.2V(6S) 0.00 0.00 0.00 V LiPo STORAGE before using with sources other than a standard AC wall outlet. CYCLE NiMH RE-PEAK ™ DISCHARGE LiFe STORAGE • User battery data, store and load up to 10 battery profiles ON 120min Banana plug to EC3 battery connector (2) SAFETY TIMER connectors before connecting cell-balancing connectors, where used). 3.0V/CELL TVC=YOUR RISK! PROGRAM SELECT BATT TYPE 0.00 0.00 0.00 V 2.0A 22.2V(6S) Input Power Low DCHG>CHG 1 2 2.0A 19.8V(6S) PROGRAM SELECT ON 11.0VCut-Off 120min • (2) 2x16 backlit, blue LCD LiIo BALANCE NiCd CHARGE LiPo DISCHARGE 4.20V 6. Start battery charging. SYSTEM SET-> LiPo Capacity Cut-Off AC power cord (one region-US, EU, AU or UK) TVC=YOUR RISK! LI BATT METER 2.0A 21.6V(6S) CURRENT 2.0A 2.0A 22.2V(6S) • Insulated, color coded, banana jack, power output terminals (Red = Positive (+), LiPo DISCHARGE MAIN 00.00V NiMH CYCLE LiFe BALANCE DISCHARGE ON 5000mAh 4.20V Capacity Cut-Off LiIo TEMPERATURE System Set NiCd VOLTS CHARGE BATT 2.0A 22.2V(6S) H0.000V Ext. Temp 0C DCHG>CHG 1 Optional Accessories 2.0A CHARGE 19.8V(6S) Black = Common or Negative (–)) ON L0.000V A. Power Output Red (+) NiCd Auto CHARGE LiIo 2.0A 21.6V(6S) CUT-OFF 50C CURRENT 2.0A Ni-Cd Batteries [BATT MEMORY 1] 7.4V(2S) Key Beep ON Int. Temp 32C5000mAh TEMPERATURE DYN4012 - DC Power Cord • Internal cooling fans with grill covers CURRENT 2.0A 2.0A 21.6V(6S) B. Power Output Black (–) ENTER SET -> Buzzer ON [BATT MEMORY 1] CUT-OFF 50C Key Beep NiCd Auto CHARGE CHARGE SAVE PROGRAM LiIo BALANCE CHARGE DYN5031 - Insulated Charge Adapter, Banana to EC3 Device • Operating temperature range of 0°C to +50°C CHARGE CURRENT LOAD FACTORY SET ENTER C. Balance Circuit Adapter ENTER SET -> PROGRAM SELECT Buzzer NiCd DISCHARGE LiIo FAST CHG CURRENT 2.0A PROGRAM SELECT 2.0A 21.6V(6S) PROGRAM SELECT K. BATT 2.2A Input Power LowON DYN5032 - Balancing Adapter Board ENTER SAVE • Meets IP33CW, IK07 environmental specs Board Connector NiCd BATT 0.1A PROGRAM CUT:TYPE 1.0V 2.0A 21.6V(6S) LiIo BATT SYSTEM SET-> LiPo PROGRAM SELECT Cut-Off BATT TYPE ENTER Input Power11.0V Low PROGRAM SELECT NiCd DISCHARGE Auto CHARGE FAST CHG DYN5033 - Temperature Sensor: DYN4103, DYN4300 LiIo CHARGE PROGRAM SELECT • Rugged industrial plastic case PROGRAM SELECT D. Temperature Probe Connection DSCH CURRENT VERSIONCut-Off SYSTEM SET-> LiPo 11.0V NiCd BATT NiCd RE-PEAK LiIo STORAGE 0.1A CUT:VOLTS 1.0V CURRENT 2.0A 2.0A 21.6V(6S) LiIo BATT J. BATT MEMORY 1.0A BATT Ext. Temp 0C 1.00 Minimum computer requirements for use of included software: Microsoft® E. Mode/Stop Key Specifications 27.4V(2S) 2.0A 21.6V(6S) Int. 32C BATT VOLTS Ext. Temp 0C PROGRAM SELECT NiCd RE-PEAK DISCHARGE LiIo STORAGE FAST CHG Windows XP®, Windows 7® or Windows Vista® operating system, Compact disk PROGRAM SELECT F. USB Communications Port DSCH VOLTAGE AC Input Voltage 100–240V AC (50/60Hz) 0.00 0.00 0.00 V Int. Temp 32C NiCd NiCd BATT LiIo DISCHARGE 27.4V(2S) 0.1A CYCLE CUT: 1.0V 2.0A 21.6V(6S) LiIo BATT (CD) reader capable of reading a mini-CD and USB 2.0 port. G. 1A USB Charge Port CHARGE CURRENT 3.0V/CELL LOAD FACTORY SET 0.00 0.00 0.00 V DCHG>CHG 1 PROGRAM 2.0A 21.6V(6S) DC Input Voltage 11–18V DC SELECT 2.2A ENTER CHARGE CURRENT H. Jog Dial LOAD FACTORY SET NiCd CYCLE DISCHARGE RE-PEAK LiIo STORAGE FEATURES TVC=YOUR RISK! LI BATT METER 2.2A Charge Current 0.10 to 10.0A per channel (in 0.1A increments/200W MAIN 00.00V ENTER DCHG>CHG 1 2 2.0A 21.6V(6S) I. LCD Screen PROGRAM SELECT • Two charging ports to charge two batteries at once. Batteries can be different Pb CHARGE 4.20V DSCH CURRENT LiPo BALANCE VERSION H0.000V L0.000V 1.00 maximum per channel/400W Total) BATT MEMORY J. AC Power Input Port 2.0A 2.0VCURRENT (1P) 1.0A 2.0A DISCHARGE 22.2V(6S) PROGRAMPROGRAM SELECT different chemistries, capacities and cell counts DSCH SELECT VERSION NiCd CYCLE LiIo TEMPERATURE Pb CHARGE LiPo BALANCE MEMORY K. Power Switch 1.0A Lithium Battery Meter Discharge Current 0.10 to 5.0A per channel (in 0.1A increments/50W Pb BATT 1.00 DCHG>CHG 1 • 1A USB charge port compatible with iPhone®, iPod® or similar products 2.0A 21.6V(6S) Pb Batteries CUT-OFF 50C Pb DISCHARGE LiPo CHARGE 2.0A 2.0VVOLTAGE (1P) DSCH 2.0A 22.2V(6S) PROGRAM SELECT 0.00 0.00 0.00 V L. DC Power Input/ maximum per channel/100W Total) • 100–240V AC (50/60Hz) or 11–18V DC input voltage 2.0A 2.0VVOLTAGE (1P) 2.0A 22.2V(6S) 3.0V/CELL DSCH Pb BATT 0.00 0.00 0.00 V SAVE PROGRAM 3.0V/CELL PROGRAM SELECT DISCHARGE Pb CHARGE CHARGE LiPo BALANCE APP Connectors • Li-Ion/Li-Po/Li-Fe battery cell count of 1 to 6 series cells Operating Temperature 0°C to +50°C 0.00 0.00 V TVC=YOUR LiPo FAST CHG 2.0A Time 2.0VENTER (1P) RISK! PROGRAM SELECT LI BATT METER 2.0A 22.2V(6S) PROGRAM SELECT PROGRAM SELECT Rest MAIN 0.00 00.00V • Ni-Cd/Ni-MH battery cell count of 1 to 15 cells Balance Current Drain 300mA per cell 4.20V 2.0A 22.2V(6S) LiPo BATT TVC=YOUR RISK! LI BATT METER Pb BATT CHG>DCHG 10min H0.000V L0.000V MAIN 00.00V CHG Pb DISCHARGE LiPo FAST CHARGE PROGRAM SELECT • Pb battery voltage of 2 to 24V 4.20V Rest Time Trickle Charge Current 50 to 200mA TEMPERATURE H0.000V L0.000V LiPo L. 2.0A 2.0V (1P) 2.0A 22.2V(6S) A. LiPo B. BATT H. C. I. D. E. F. STORAGE G. • Built-in 50W discharger SAFETY TIMER CHG>DCHG 10min CUT-OFF 50C 2.0A 22.2V(6S) TEMPERATURE Charging Mode Peak (Ni-Cd/Ni-MH), CC/CV (Li-Po/Li-Ion/Li-Fe/Pb) ON 120min • Built-in balance circuit STORAGE LiPo FAST CHG PROGRAM SELECT CUT-OFF 50C SAFETY TIMER Rest Time SAVE PROGRAM LiPo DISCHARGE 2.0A 22.2V(6S) LiPo BATT Capacity Cut-Off ON 120min CHG>DCHG 10min ENTER 2.0A 22.2V(6S) SAVE PROGRAM ON 5000mAh DISCHARGE LiPo STORAGE Capacity Cut-Off ENTER SAFETY TIMER 2.0A 22.2V(6S) Li-Fe Balance Charging Li-Fe DischargING Li-Io Charging [BATT MEMORY 1] Key Beep 5000mAh ON ON 120min SETPress -> the Mode key until you reach the 9 main menus, Buzzer ON LiPo ENTER DISCHARGE then rotate the Jog Dial To select values other than the existing parameters: [BATT MEMORY 1] Key Beep Cut-Off ON Capacity Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial To select values other than the existing parameters: Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial To select values other than the existing parameters: 2.0A ENTER 22.2V(6S) PROGRAM SELECT BATT TYPE SET -> Input Power Low to locate the PROGRAM SELECT LiIo BATT screen. Press the Jog Dial to go into Buzzer ON ON 5000mAh • Press the Jog Dial so the charge current value (A) flashes to locate the PROGRAM SELECT LiFe BATT screen. Press the Jog Dial to go into to locate the PROGRAM SELECT LiFe BATT screen. Press the Jog Dial to go into • Press the Jog Dial so the discharge current value (A) flashes SYSTEM SET-> • Press the Jog Dial so the charge current value (A) flashes LiPo Cut-Off 11.0V this menu.PROGRAM SELECT • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value BATT TYPE this menu. [BATT MEMORY 1] Input Power Low Key Beep ON this menu. • Rotate the Jog Dial to INCREASE OR DECREASE the discharge current value • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value SYSTEM SET-> BATT VOLTS LiPo ENTER SET -> Ext. Temp 0C Rotate the Jog Dial to go to the LiIo CHARGE screen and set charging parameters. • Press the Jog Dial to save the value and the voltage value (B) flashes Cut-Off 11.0V Buzzer ON Rotate the Jog Dial to go to the LiFe DISCHARGE screen and set discharging • Press the Jog Dial to save the value and the voltage value (B) flashes Rotate the Jog Dial to go to the LiFe BALANCE screen and set charging param• Press the Jog Dial to save the value and the voltage value (B) flashes 7.4V(2S) Int. TempVoltage (B) 32C The charging amperage (A) can be set between 0.1 and 10.0A. is • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in PROGRAM SELECT TYPE parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. Volt• Rotate the Jog Dial to INCREASE OR DECREASE the voltageBATT (and # ofVOLTS cells in Ext. Temp Input Power Low0C eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in dependent on the number of cells in series. For example, with Li-Io batteries these series (C)) SYSTEM SET-> CHARGE CURRENT LiPo 7.4V(2S) LOAD FACTORY SET Int. Temp 32C Cut-Off 11.0V age (B) is dependent on the number of cells in series. For example, with Li-Fe batseries (C)) is dependent on the number of cells in series. For example, with Li-Fe batteries series (C)) 2.2A values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries). ENTER • Press the Jog Dial to save the voltage value teries these values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries). • Press the Jog Dial to save the voltage value these values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries). • Press the Jog Dial to save the voltage value CHARGE CURRENT BATT VOLTS LOAD FACTORY SET Ext. Temp 0C If no parameters are flashing, you can rotate the Jog Dial to select another PROGRAM SELECT DSCH CURRENT 2.2A 7.4V(2S) VERSION Int. Temp ENTER 32C A battery’s capacity can be verified by discharging it to its minimum voltage level If no parameters are flashing, you can rotate the Jog Dial to select another If no parameters are flashing, you can rotate the Jog Dial to select another BATT MEMORY 1.0A program such as BALANCE, FAST CHG, STORAGE or DISCHARGE. 1.00 and measuring the current as the battery is discharged. program such as CHARGE, BALANCE, FAST CHG or STORAGE. PROGRAM SELECT program such as CHARGE, FAST CHG, STORAGE or DISCHARGE. DSCH CURRENT CHARGE CURRENT VERSION LOAD FACTORY SET To start charging, press and hold the Jog Dial for 3 seconds. BATT MEMORY 2.2A 1.00 ENTER To start discharging, press and hold the Jog Dial for 3 seconds.DSCH VOLTAGE1.0A To start charging, press and hold the Jog Dial for 3 seconds. 0.00 0.00 0.00 V 3.0V/CELL 0.00 0.00 0.00 V CAUTION: If at any time during the charge process the battery becomes PROGRAM SELECT DSCH VOLTAGE CURRENT PROGRAM SELECT VERSION 0.00 0.00 0.00 V TVC=YOUR RISK! BATT MEMORY hot or begins to puff, disconnect the battery immediately and discontinue 3.0V/CELL 1.0A LI BATT METER 1.00 MAIN 00.00V 0.00 0.00 0.00 V PROGRAM SELECT B 4.20V A the charge process as batteries can cause fire, collateral damage and A B C H0.000V CL0.000V TVC=YOUR RISK! DSCH VOLTAGE LI BATT METER MAIN 00.00V injuries. 0.00 0.00 0.00 V TEMPERATURE 4.20V 3.0V/CELL H0.000V L0.000V 0.00 0.00 0.00 V Li-Fe Charging PROGRAM SELECT CUT-OFF 50C A B C TEMPERATURE TVC=YOUR RISK! LI BATT METER MAIN 00.00V To select values other than the existing parameters: Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial SAVE PROGRAM CUT-OFF 50C Li-Io Fast Charging 4.20V H0.000V L0.000V ENTER to locate the PROGRAM SELECT LiFe BATT screen. Press the Jog Dial to go into • Press the Jog Dial so the charge current value (A) flashes SAVE PROGRAM Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial TEMPERATURE this menu. • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value ENTER CUT-OFF 50C to locate the PROGRAM SELECT LiIo BATT screen. Press the Jog Dial to go into • Press the Jog Dial to save the value and the voltage value (B) flashes Rotate the Jog Dial to go to the LiFe CHARGE screen and set charging param this menu. Li-Io BATTERIES SAVE PROGRAM • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) ENTER Rotate the Jog Dial to go to the LiIo FAST CHG screen and set charging paramJST_XH ADAPTER 2S 3S 4S JST_XH ADAPTER 5S 6S 2S 3S 4S 5S 6S 3 7 LiFe BALANCE 5.5A19.8V(6S) 11 is dependent on the number of cells in series. For example, with Li-Fe batteries these values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries). LiFe CHARGE 4.6A19.8V(6S) A 5 B C 6 series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as BALANCE, FAST CHG, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. AUTION: If at any time during the charge process the battery becomes C hot or begins to puff, disconnect the battery immediately and discontinue the charge process as batteries can cause fire, collateral damage and injuries. Li-Fe Fast Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiFe BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiFe FAST CHG screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Fe batteries these values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries). Near the end of a standard charging cycle, the charger switches from Constant Current (CC) mode to Constant Voltage (CV) mode to slowly “top off” the current in the battery as close as possible to the maximum capacity. In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging time; however, the final capacity of the battery will be less than what you would get using the standard charge method. LiIo CHARGE 4.6A21.6V(6S) LiFe DISCHARGE 2.0A19.8V(6S) 4 10 LiFe FAST CHG 0.1A19.8V(6S) A B C To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. Li-Fe Storage Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiFe BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiFe STORAGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Fe batteries these values can be from 3.3V (for 1S batteries) to 19.8V (for 6S batteries). If you don’t plan on using your battery for a long time, it is best to charge (or discharge) the battery to its optimal storage voltage and capacity. LiFe STORAGE 2.5A19.8V(6S) A B C To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, FAST CHG or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. 8 Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiIo BATT screen. Press the Jog Dial to select LiIo. Rotate the Jog Dial to go to one of the control screens (BALANCE, CHARGE, FAST CHG, STORAGE or DISCHARGE) to do what your battery needs. Correctly connect your lithium battery to the charger (charging connector first and balancing connector second). Press the Jog Dial and adjust the charging parameters as needed. Press and hold the Jog Dial (approximately 3 seconds) until the screen changes to start the battery check/charge sequence. A When the charge cycle starts, the charger compares the battery to charger settings. The screen will show the battery and your settings information. If the information after R: (charger) and S: (settings) (A) does not match, press the Mode key and change the lithium battery charging parameters as needed. If the R: information matches S:, press the Jog Dial to confirm. After confirmation, charging starts and information will show on the LCD screen (information may vary). R: 3SER S:3SER CONFIRM(ENTER) 9 BCD A LI 3S 2.0A 12.59V BAL 022:43 01082 A. A Li-Io battery pack is balance charging B. Battery pack has 3 cells in series F E C. Charging rate is 2.0A (2000mAh) D. Voltage being applied to the battery is currently 12.59V E. Present charge level of the battery is 1082mAh F. Time elapsed since the charge process started is 22:43 During charging, the Jog Dial can be rotated counterclockwise to show several parameter messages on the LCD screen, including: End Voltage, Input Power Voltage, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and Capacity Cutoff. Rotate the Jog Dial clockwise to show the charge voltages for each cell. Press the Jog Dial at any time to return to the Charge Monitor screen. The charger signals when the charging (or discharging) process is complete (if Buzzer is set to ON). AUTION: The Li-Io program menus are to be used ONLY for the C charging and discharging of Li-Io batteries. The charging of other battery types using these programs will result in damage to the battery or charger. CAUTION: Using a charge rate that is not compatible with the battery capacities may result in damage or malfunction of the charger or batteries. eters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Io batteries these values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries). Near the end of a standard charging cycle, the charger switches from Constant Current (CC) mode to Constant Voltage (CV) mode to slowly “top off” the current in the battery as close as possible to the maximum capacity. In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging time; however, the final capacity of the battery will be less than what you would get using the standard charge method. 12 LiIo BALANCE 5.5A21.6V(6S) A B C To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, FAST CHG, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. A B C To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. Li-Io Storage Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiIo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiIo STORAGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Io batteries these values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries). If you don’t plan on using your battery for a long time, it is best to charge (or discharge) the battery to its optimal storage voltage and capacity. LiIo STORAGE 2.5A21.6V(6S) Li-Io Balance Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiIo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiIo BALANCE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Io batteries these values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries). LiIo FAST CHG 5.0A21.6V(6S) A 13 B To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, FAST CHG or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. 2 NiMH CYCLE DCHG>CHG 1 NiMH CHARGE NiCd CHARGE 2.0A CURRENT CURRENT 2.0A NiMH Auto CHARGE NiCd Auto CHARGE CURRENT 2.0A CURRENT 2.0A (DYN4300) NiMH DISCHARGE PROGRAM SELECT PROGRAMNiMH SELECT NiCd DISCHARGE 0.1A CUT:1.0V NiCd BATT BATT 0.1A CUT: 1.0V NiMH RE-PEAK OPERATING YOUR CHARGER NiCd RE-PEAK TAble of CONTENTS 2 2 1 SELF TEST AND PROGRAM SELECT SCREENS Programming and Operations NiMH CYCLE 18 Li-Po Storage Charging NiCd CYCLE 19 Li-Po Discharge 35 BATTERY MEMORY LI-FE DCHG>CHG 1 DCHG>CHG 1 36 SYSTEM SET 2 Li-Fe BATTERIES Ni-MH a REST TIME NiCd CHARGE 20 Ni-MH BATTERIES 3 Li-Fe Balance Charging Pb CHARGE CURRENT 2.0V 21 2.0A b SAFETY TIMER 4 Li-Fe Charging Ni-MH Charging 2.0A (1P) PROGRAM SELECT c CAPACITY CUTOFF 5 Li-Fe Fast Charging 22 Ni-MH Auto Charging NiCd Auto CHARGE Pb BATT Pb DISCHARGE2.0A d KEY BEEP/BUZZER CURRENT 6 Li-Fe Storage Charging 2.0A 23 Ni-MH Discharge 2.0V (1P) e INPUT POWER LOW CUTOFF 7 Li-Fe Discharge 24 Ni-MH Re-Peak Charging PROGRAM SELECT NiCd DISCHARGE f EXTERNAL AND INTERNAL TEMPERATURES Ni-MH Cycle Charging 0.1A Time CUT: 25 1.0V Rest Li-IO NiCd BATT g RESET FACTORY SETTINGS CHG>DCHG 10min 8 Li-Io BATTERIES NiCd RE-PEAKNI-CD h VERSION 9 Li-Io Balance Charging SAFETY TIMER26 Ni-CD 2 BATTERIES 37 Li BATTERY VOLTAGE CHECKER OPERATION - USON 120min 10 Li-Io Charging NiCd CYCLE 27 Ni-CD Charging ING THE BALANCE ADAPTER PORT 11 Li-Io Fast Charging 28 Ni-CD DCHG>CHG Cut-Off 1 Auto Charging Capacity 38 USB ACCESSORY CHARGER OPERATION (COM12 Li-Io Storage Charging ON 29 Ni-CD Discharge 5000mAh PATIBLE WITH iPhone and iPod DEVICES) Pb CHARGE 13 Li-Io Discharge 30 Ni-CD Re-Peak Charging Key Beep ON 39 Troubleshooting Guide 2.0A 2.0V (1P) 31 Ni-CD Cycle Charging PROGRAM SELECT Li-PO Buzzer ON Pb BATT Pb DISCHARGEPB 14 Li-Po BATTERIES PROGRAM SELECT Input Power Low 2.0A 2.0V 32 (1P) 15 SYSTEM Li-Po Balance Charging Pb BATTERIES SET-> Cut-Off 11.0V 16 Li-Po Charging 33 Pb Charging Rest Time Ext. Temp 17 Li-Po Fast Charging 34 0C Pb Discharge CHG>DCHG Int. Temp 10min 32C SAFETY TIMER SET SELF TEST AND PROGRAM SELECT SCREENS LOAD FACTORY ON 120min ENTER When the charger is powered ON, there is a series of self tests and the screen will After the self tests, the charger will show another screen. The information on this Capacity Cut-Off VERSION show the charger brand name and model number. screen will vary but will look similar to this: ON 5000mAh 1.00 LiPo BALANCE Key Beep 0.00 0.00 0.00 VON Buzzer ON 2.0A7.4V(2S) 0.00 0.00 0.00 V PROGRAM SELECT PROGRAM SELECT Input Power Low LI BATT METER From any screen, press the Mode key to go back to the main menu. MAIN 00.00V 11.0V SYSTEM SET-> Cut-Off H0.000V L0.000V Li-Fe BATTERIES Ext. Temp 0C Int. Temp 32C Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to During charging, the Jog Dial can be rotated counterclockwise to show several locate the PROGRAM SELECT LiFe LOAD BATT screen. Press the SET Jog Dial to select LiFe. parameter messages on the LCD screen, including: End Voltage, Input Power VoltFACTORY Rotate the Jog Dial to go to one of the control screens ENTER (BALANCE, CHARGE, FAST age, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and Capacity Cutoff. CHG, STORAGE or DISCHARGE) to do what your battery needs. VERSION Rotate the Jog Dial clockwise to show the charge voltages for each cell. Press the 1.00 Correctly connect your lithium battery to the charger (charging connector first and 1 DYNAMITE DYN4300 2 Jog Dial at any time to return to the Charge Monitor screen. The charger signals balancing connector second). Press the Jog Dial and adjust charging parameters 0.00 0.00 0.00 V when the charging (or discharging) process is complete (if Buzzer is set to ON). as needed. Press and hold the Jog0.00 Dial (approximately 3 seconds) until the screen 0.00 0.00 V PROGRAM SELECT changes to start METER the battery check/charge sequence. CAUTION: The Li-Fe program menus are to be used ONLY for the LI BATT MAIN 00.00V A When the charge cycle starts, the charging and discharging of Li-Fe batteries. The charging of other battery H0.000V L0.000V charger compares the battery to the types using these programs will result in damage to the battery or charger. charger settings. The screen will show CAUTION: Using a charge rate that is not compatible with the battery the battery and your settings capacities may result in damage or malfunction of the charger or information. If the information after R: (charger) and S: (settings) (A) does not match, batteries. press the Mode key and change the lithium battery charging parameters as needed. If the R: information matches S:, press the Jog Dial to confirm. After confirmation, charging starts and information will show on the LCD screen (information may vary). BCD A. A Li-Fe battery pack is balance charging B. B attery pack has 3 cells in A series F E C. Charging rate is 2.0A (2000mAh) D. Voltage being applied to the battery is currently 12.59V E. Present charge level of the battery is 1082mAh F. Time elapsed since the charge process started is 22:43 (22 minutes and 43 seconds) R: 3SER S:3SER CONFIRM(ENTER) LI 3S 2.0A 12.59V BAL 022:43 01082 • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value 14 Li-Io DischargING LiIo DISCHARGE 2.0A21.6V(6S) A B C To select values other than the existing parameters: • Press the Jog Dial so the discharge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the discharge current value • Press the Jog Dial to save the value and the voltage value (B) flashes If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, FAST CHG or STORAGE. To start discharging, press and hold the Jog Dial for 3 seconds. Li-Po BATTERIES Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to select LiPo. Rotate the Jog Dial to go to one of the control screens (BALANCE, CHARGE, FAST CHG, STORAGE or DISCHARGE) to do what your battery needs. Correctly connect your lithium battery to the charger (charging connector first and balancing connector second). Press the Jog Dial and adjust the charging parameters as needed. Press and hold the Jog Dial (approximately 3 seconds) until the screen changes to start the battery check/charge sequence. A When the charge cycle starts, the charger compares the battery to the charger settings. The screen will show the battery and your settings information. If the information after R: (charger) and S: (settings) (A) does not match, press the Mode key and change the lithium battery charging parameters as needed. If the R: information matches S:, press the Jog Dial to confirm. After confirmation, charging starts and information will show on the LCD screen (information may vary). R: 3SER S:3SER CONFIRM(ENTER) 15 BCD A LI 3S 2.0A 12.59V BAL 022:43 01082 A. A Li-Po battery pack is balance charging B. B attery pack has 3 cells in series F E C. Charging rate is 2.0A (2000mAh) D. Voltage being applied to the battery is currently 12.59V E. Present charge level of the battery is 1082mAh F. Time elapsed since the charge process started is 22:43 During charging, the Jog Dial can be rotated counterclockwise to show several parameter messages on the LCD screen, including: End Voltage, Input Power Voltage, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and Capacity Cutoff. Rotate the Jog Dial clockwise to show the charge voltages for each cell. Press the Jog Dial at any time to return to the Charge Monitor screen. The charger signals when the charging (or discharging) process is complete (if Buzzer is set to ON). AUTION: The Li-Po program menus are to be used ONLY for the C charging and discharging of Li-Po batteries. The charging of other battery types using these programs will result in damage to the battery or charger. CAUTION: Using a charge rate that is not compatible with the battery capacities may result in damage or malfunction of the charger or batteries. Li-Po Balance Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiPo BALANCE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Po batteries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries). LiPo BALANCE 5.5A22.2V(6S) A B To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, FAST CHG, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. C 16 Li-Po Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiPo CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Po batteries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries). C Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiIo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiIo DISCHARGE screen and set discharging parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Io batteries these values can be from 3.6V (for 1S batteries) to 21.6V (for 6S batteries). A battery’s capacity can be verified by discharging it to its minimum voltage level and measuring the current as the battery is discharged. NiMH RE-PEAK LiPo CHARGE 4.6A22.2V(6S) A B C To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as BALANCE, FAST CHG, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. AUTION: If at any time during the charge process the battery becomes C hot or begins to puff, disconnect the battery immediately and discontinue the charge process as batteries can cause fire, collateral damage and injuries. 17 24 Li-Po Fast Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiPo FAST CHG screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Po batteries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries). Near the end of a standard charging cycle, the charger switches from Constant Current (CC) mode to Constant Voltage (CV) mode to slowly “top off” the current in the battery as close as possible to the maximum capacity. In Fast Charge, the CV mode is eliminated in order to greatly shorten the charging time; however, the final capacity of the battery will be less than what you would get using the standard charge method. 18 LiPo FAST CHG 4.0A7.4V(2S) A B Li-Po Storage Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiPo STORAGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Po batteries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries). If you don’t plan on using your battery for a long time, it is best to charge (or discharge) the battery to its optimal storage voltage and capacity. LiPo STORAGE 2.5A11.1V(3S) A 19 B To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, FAST CHG or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. Li-Po DischargING LiPo DISCHARGE 2.0A22.2V(6S) A B To select values other than the existing parameters: • Press Jog Dial so the discharge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the discharge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, FAST CHG or STORAGE. To start discharging, press and hold the Jog Dial for 3 seconds. A B C NiMH 2.0A 7.59V CHG022:43 01082 A. A Ni-MH battery pack is charging B. Charging rate is 2.0A (2000mAh) Ni-MH Cycle Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiMH CYCLE screen and set charge/discharge cycle count parameters. The battery can be put through a series of charge/discharge cycles using this program. Cycling Ni-MH batteries can increase capacity and rejuvenate neglected batteries. Discharge capacity and average battery voltage help you compare batteries for the best run time and power. During charging, the Jog Dial can be rotated counterclockwise to show several parameter messages on the LCD screen, including: Ni-MH Sensitivity, Input Power Voltage, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and Capacity Cutoff. The charger signals when the charging (or discharging) process is complete (if Buzzer is set to ON). AUTION: The Ni-MH program menus are to be used ONLY for the C charging and discharging of Ni-MH battery packs. The charging of other battery types using these programs will result in damage to the battery or charger. CAUTION: Using a charge rate that is not compatible with the battery capacities may result in damage or malfunction of the charger or batteries. A 26 Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to select NiCd. Rotate the Jog Dial to go to one of the control screens (CHARGE, Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE) to do what your battery needs. Correctly connect your Ni-Cd battery to the charger. Press the Jog Dial and adjust the charging parameters as needed. Press and hold the Jog Dial (approximately 3 seconds) until the screen changes to start the battery check/charge sequence. After confirmation, charging starts and information will show on the LCD screen (information may vary). A C NiCd 2.0A 7.59V CHG022:43 01082 NiMH CHARGE CURRENT1.0A To select a value other than the existing parameter: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE. To start charging, press and hold the Jog Dial for 3 seconds. A 22 A. A Ni-Cd battery pack is charging B. Charging rate is 2.0A (2000mAh) NiMH Auto CHARGE CURRENT1.0A To select a value other than the existing parameter: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, DISCHARGE, RE-PEAK or CYCLE. To start charging, press and hold the Jog Dial for 3 seconds. NiCd CHARGE CURRENT1.0A NiMH DISCHARGE 0.1A CUT: 1.0V B AUTION: The Ni-Cd program menus are to be used ONLY for the C charging and discharging of Ni-Cd battery packs. The charging of other battery types using these programs will result in damage to the battery or charger. CAUTION: Using a charge rate that is not compatible with the battery capacities may result in damage or malfunction of the charger or batteries. To select a value other than the existing parameter: • Press the Jog Dial so the discharge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the discharge current value • Press the Jog Dial to save the value and the cutoff voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the cutoff voltage • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, RE-PEAK or CYCLE. To start discharging, press and hold the Jog Dial for 3 seconds To select a value other than the existing parameter: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE. To start charging, press and hold the Jog Dial for 3 seconds. Ni-CD Auto Charging To select a value other than the existing parameter: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, DISCHARGE, RE-PEAK or CYCLE. To start charging, press and hold the Jog Dial for 3 seconds. A A B 34 Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT Pb BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the Pb DISCHARGE screen and set discharging parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. A battery’s capacity can be verified by discharging it to its minimum voltage level and measuring the current as the battery is discharged. The discharge level can be set from 2 to 20V. 35 F E C. Charging at a rate of 0.4A (400mAh) D. Voltage being applied to the battery is currently 12.39V E. Present charge level of the battery is 1082mAh F. Time elapsed since the charge process started is 22:43 During charging, the Jog Dial can be rotated counterclockwise to show several parameter messages on the LCD screen, including: End Voltage, Capacity Cutoff, Safety Timer Status, Temperature Cutoff and Input Power Voltage. The charger signals when the charging (or discharging) process is complete (if Buzzer is set to ON). AUTION: The Pb program menus are to be used ONLY for the charging C and discharging of Pb battery packs. The charging of other battery types using these programs will result in damage to the battery or charger. CAUTION: Using a charge rate that is not compatible with the battery capacities may result in damage or malfunction of the charger or batteries. To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the charge current value and the battery voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the battery voltage/cell count value (Pb batteries are 2.0V per cell, for a 6 cell battery this would be 2.0V x 6 cell = 12.0V) • Press the Jog Dial to save the voltage If no parameters are flashing, you can rotate the Jog Dial to select another program such as DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. To select values other than the existing parameters: • Press the Jog Dial so the discharge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the discharge current value • Press the Jog Dial to save the value and the cutoff voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the cutoff voltage • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE. To start discharging, press and hold the Jog Dial for 3 seconds BATTERY MEMORY Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT BATT MEMORY screen. Press the Jog Dial to select BATT MEMORY. Use this menu to create a battery profile. To reduce the time required to initiate a charging or discharging cycle on a battery you regularly use, this charger has been designed with the capability of storing up to 10 battery profiles that can be quickly accessed and run at a later time. • Rotate the Jog Dial to identify a battery profile, 1 through 10 • Press the Jog Dial to select battery profile 1 • Press the Jog Dial so battery type flashes • Rotate the Jog Dial to select a battery type • Press the Jog Dial to save the battery type Follow this process using the Jog Dial to select, change, then save each parameter (battery voltage, charge current, discharge current, discharge voltage, Terminal Voltage Control (TVC) and temperature cutoff). Then save the battery profile. 29 Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiCd DISCHARGE screen and set discharging parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. A battery’s capacity can be verified by discharging it to its minimum voltage level and measuring the current as the battery is discharged. The discharge level can be set from 0.1 to 25.2V. NiCd DISCHARGE 0.1A CUT: 1.0V To select a value other than the existing parameter: • Press the Jog Dial so the discharge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the discharge current value • Press the Jog Dial to save the value and the cutoff voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the cutoff voltage • Press the Jog Dial to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, RE-PEAK or CYCLE. To start discharging, press and hold the Jog Dial for 3 seconds 30 Ni-CD Re-Peak Charging NiCd RE-PEAK 1 31 To select a value other than the existing parameter: • Press the Jog Dial so the re-peak value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, DISCHARGE or CYCLE. Press the Jog Dial to go to the next menu. Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiCd CYCLE screen and set charge/discharge cycle count parameters. The battery can be put through a series of charge/discharge cycles using this program. Cycling Ni-Cd batteries can increase capacity and rejuvenate neglected batteries. Discharge capacity and average battery voltage help you compare batteries for the best run time and power. NiCd CYCLE CHG>DCHG5 B To select values other than the existing parameter: • Press the Jog Dial so the cycle type (A) flashes • Rotate the Jog Dial to set the cycle type as CHG>DCHG or DCHG>CHG • Press the Jog Dial to save your choice and the number of cycles (B) flashes • Rotate the Jog Dial to set the cycle count between 1 to 5 • Press the Jog Dial to save the cycle count value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, DISCHARGE or RE-PEAK. To start cycling, press and hold the Jog Dial for 3 seconds. AUTION: Increasing the TVC value beyond the default settings may result in a C shorter battery life and/or damage to the battery. Do not change the TVC value unless you fully understand the effects TVC will have on your battery. To Charge or Discharge a battery using the saved profile: Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT BATT MEMORY screen. Press the Jog Dial to select BATT MEMORY. • Rotate the Jog Dial to identify the battery profile, 1 through 10. • Press and hold the Jog Dial for 3 seconds • Rotate the Jog Dial to choose the type of charge function you wish to perform • Press and hold the Jog Dial for 3 seconds to start Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT SYSTEM SET screen. Press the Jog Dial to select SYSTEM SET. Use this menu to set the “behind the scenes” operating parameters for this charger such as; Rest Time, Safety Timer, Capacity Cutoff, Key Beep/Buzzer, Input Power Low Cutoff, External and Internal Temperatures, Load Factory Settings and Version. d KEY BEEP/BUZZER e INPUT POWER LOW CUTOFF f EXTERNAL AND INTERNAL TEMPERATURES REST TIME Use this menu to set the Rest time during each step in a cycle.When a Ni-MH or Ni-CD battery is cycled (charged, discharged and charged again) it will get hot, therefore it is necessary to set a rest time interval during each step of the process to make sure the battery and charger are completely cooled before moving on to the next part of the cycle. Default time is 10 minutes, but this can be set between 1 and 60 minutes. To select a value other than the default parameter: • Press the Jog Dial to select Rest Time • Press the Jog Dial so the Rest Time value flashes • Rotate the Jog Dial to select Rest Time in Minutes • Press the Jog Dial to save the Rest Time value • Rotate the Jog Dial to select SAFETY TIMER Use this menu to set the key beep and charger alarm buzzer at ON or OFF as needed. We recommend that you keep the alarm ON so the alarm will sound when charging is complete or if there is cause for alarm during charging. To select values other than the default parameters: • Press the Jog Dial so the Key Beep ON/OFF value flashes • Rotate the Jog Dial to select ON or OFF • Press the Jog Dial to save the value • Press the Jog Dial so the Buzzer ON/OFF value flashes • Rotate the Jog Dial to select ON or OFF • Press the Jog Dial to save the value • Rotate the Jog Dial to select Input Power Low Cutoff SAFETY TIMER Use this menu to set a time limit for charging a battery. When a charge cycle is started, a clock inside the charger will begin recording the elapsed charge time. If the SAFETY TIMER function has been turned ON, the charger will stop the charging process once this time limit has been reached to avoid damage caused by over-charging the battery. This time value can be set between 1 and 720 minutes. To select values other than the default parameters: • Press the Jog Dial so the ON/OFF value flashes • Rotate the Jog Dial to select ON or OFF • Press the Jog Dial to save the value • Rotate the Jog Dial to select the value for time • Press the Jog Dial to save the value • Rotate the Jog Dial to select Capacity Cutoff CAPACITY CUTOFF c Ni-CD Cycle Charging Rotate the Jog Dial to select SAVE PROGRAM Press the Jog Dial to save the program Repeat this process to enter additional battery profiles Press the Mode key until you reach the 9 main menus SYSTEM SET b B • • • • 36 A Pb-60.4A12.39V CHG022:43 01082 A A. A Lead Acid battery pack is charging B. Battery pack has 6 cells in series Pb DischargING a Ni-CD DischargING Ni-MH DischargING Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiMH DISCHARGE screen and set discharging parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. A battery’s capacity can be verified by discharging it to its minimum voltage level and measuring the current as the battery is discharged. The discharge level can be set from 0.1 to 25.2V. During charging, the Jog Dial can be rotated counterclockwise to show several parameter messages on the LCD screen, including: Ni-Cd Sensitivity, Input Power Voltage, External & Internal Temperature, Temperature Cutoff, Safety Timer Status and Capacity Cutoff. The charger signals when the charging (or discharging) process is complete (if Buzzer is set to ON). A 28 A CD A B Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiCd RE-PEAK screen and set re-peak parameters to a value of between 1 and 3. A 23 Pb CHARGE 0.1A 2.0V (1P) Pb DISCHARGE 0.1A 2.0V (1P) Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiCd CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Ni-MH Auto Charging Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiMH Auto CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT Pb BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the Pb CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. ED C. Voltage being applied to the battery is currently 7.59V D. Present charge level of the battery is 1082 mAh E. Time elapsed since the charge process started is 22:43 Ni-MH Charging A B NiCd Auto CHARGE CURRENT1.0A Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiMH CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. 33 B Pb Charging B Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiCd BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiCd Auto CHARGE screen and set charging parameters. The charging amperage (A) can be set between 0.1 and 10.0A. ED C. Voltage being applied to the battery is currently 7.59V D. Present charge level of the battery is 1082 mAh E. Time elapsed since the charge process started is 22:43 21 To select values other than the existing parameter: • Press the Jog Dial so the cycle type (A) flashes • Rotate the Jog Dial to set the cycle type as CHG>DCHG or DCHG>CHG • Press the Jog Dial to save your choice and the number of cycles (B) flashes • Rotate the Jog Dial to set the cycle count between 1 to 5 • Press the Jog Dial to save the cycle count value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, DISCHARGE or RE-PEAK. To start cycling, press and hold the Jog Dial for 3 seconds. NiMH CYCLE CHG>DCHG5 37 Li BATTERY VOLTAGE CHECKER OPERATION - USING THE BALANCE ADAPTER PORT Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT Pb BATT screen. Press the Jog Dial to select Pb. Rotate the Jog Dial to go to one of the control screens (CHARGE or DISCHARGE) to do what your battery needs. The nature of a Lead Acid or Sealed Lead Acid battery is very different from that of Lithium, Ni-MH or Ni-Cd batteries. The output current of a Pb battery is lower than other batteries relative to their capacities. Furthermore, lead acid batteries can’t be charged at a level greater than 1/10 their capacity. For example, a 5000mAh lead acid battery can’t be charged at a rate greater than 0.5A. For more details on the charge and discharge capabilities of your battery, please refer to the charging data supplied by the battery manufacturer. Correctly connect your Pb battery to the charger. Press the Jog Dial and adjust the charging parameters as needed. Press and hold the Jog Dial (approximately 3 seconds) until the screen changes to start the battery check/charge sequence. After confirmation, charging starts and information will show on the LCD screen (information may vary). Ni-CD Charging Ni-MH BATTERIES Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to select NiMH. Rotate the Jog Dial to go to one of the control screens (CHARGE, Auto CHARGE, DISCHARGE, RE-PEAK or CYCLE) to do what your battery needs. Correctly connect your Ni-MH battery to the charger. Press the Jog Dial and adjust the charging parameters as needed. Press and hold the Jog Dial (approximately 3 seconds) until the screen changes to start the battery check/charge sequence. After confirmation, charging starts and information will show on the LCD screen (information may vary). 25 27 C 20 NiMH RE-PEAK 1 To select a value other than the existing parameter: • Press the Jog Dial so the re-peak value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the value • Press the Jog Dial to save the value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, Auto CHARGE, DISCHARGE or CYCLE. Press the Jog Dial to go to the next menu. Ni-CD BATTERIES C Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LiPo BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the LiPo DISCHARGE screen and set discharging parameters. The discharging amperage (A) can be set between 0.1 and 5.0A. Voltage (B) is dependent on the number of cells in series. For example, with Li-Po batteries these values can be from 3.7V (for 1S batteries) to 22.2V (for 6S batteries). A battery’s capacity can be verified by discharging it to its minimum voltage level and measuring the current as the battery is discharged. 32 Pb BATTERIES Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT NiMH BATT screen. Press the Jog Dial to go into this menu. Rotate the Jog Dial to go to the NiMH RE-PEAK screen and set re-peak parameters to a value of between 1 and 3. C To select values other than the existing parameters: • Press the Jog Dial so the charge current value (A) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the charge current value • Press the Jog Dial to save the value and the voltage value (B) flashes • Rotate the Jog Dial to INCREASE OR DECREASE the voltage (and # of cells in series (C)) • Press the Jog Dial again to save the voltage value If no parameters are flashing, you can rotate the Jog Dial to select another program such as CHARGE, BALANCE, STORAGE or DISCHARGE. To start charging, press and hold the Jog Dial for 3 seconds. Ni-MH Re-Peak Charging Use this menu to set a capacity limit at which the charger will stop charging a battery. When a charge cycle starts, the charger records the battery capacity. When the Capacity Cutoff function is set at ON, the charger will stop charging at the capacity limit to prevent battery damage. Capacity can be adjusted between 100 and 50,000mAh. • Press the Jog Dial so the ON/OFF value flashes • Rotate the Jog Dial to select ON or OFF • Press the Jog Dial to save the value • Rotate the Jog Dial to select the Capacity Cutoff value • Press the Jog Dial to save the value • Rotate the Jog Dial to select Key Beep/Buzzer Use this menu to set the input voltage limit so an alarm will sound if the voltage goes below the cutoff value. The voltage alarm value can be set anywhere from 10.0 to 11.0V. To select a value other than the default parameter: • Press the Jog Dial so the voltage value flashes • Rotate the Jog Dial to select the voltage value • Press the Jog Dial to save the value • Rotate the Jog Dial to select External and Internal Temperatures By selecting the External and Internal Temperatures Screen you can view the current temperatures of both the battery (external) and the charger (internal). The optional temperature sensor (DYN5033) is required for external temperature measurement. g RESET FACTORY SETTINGS h VERSION • Press the Jog Dial to reset the charger to factory settings • Press the Jog Dial to select VERSION By selecting the Version Screen you can view the version (revision number) of the software on your charger. You may exit this menu at any time by pressing the Mode key to return to the main menus. The Passport™ Ultra Duo charger has the capability to read and display the individual cell voltages of a Li-Po, Li-Fe or Li-Io battery. This voltage checking function can only be used when the charger is powered ON and not charging a battery. To use the voltage checker, connect the balance port connector of your Li-Po, Li-Fe or Li-Io battery to the balance adapter board connected to the Balance Circuit Adapter Board Connector (C). Press the Mode key until you reach the 9 main menus, then rotate the Jog Dial to locate the PROGRAM SELECT LI BATT METER screen. Press the Jog Dial to select LI BATT METER. In a few moments, the charger will begin to display the cell voltages of the battery in the following format: 3.70 3.70 0.00 V 0.00 0.00 0.00 V 38 This example is for a 2S battery, so only the voltages for these two cells are displayed. The data is presented in this format: 1–1 1–4 1–2 1-5 1–3 V 1–6 V At this point, you can rotate the Jog Dial to see a display of the overall battery voltage as well as the individual high- and low-cell voltage values. MAIN08.20V H4.104VL4098V You may exit this menu at any time by pressing the Mode key to return to the main menus. USB ACCESSORY CHARGER OPERATION (COMPATIBLE WITH iPhone and iPod DEVICES) The Passport Ultra Duo charger has the capability to charge your iPhone, iPod or USB compatible device with the 1A USB charge port (E). To use the charging function, simply connect a compatible charging device or cord into the charge port while the charger is powered ON. The internal USB charge port will provide up to 1A current at 5V DC. 39 Troubleshooting Guide LCD Screen Warning and Error messages shown below. During charger operation, circuits monitor battery and charger functions. If the following messages show on the charger’s LCD screen, make the recommended responses. If the message continues after you respond as recommended, contact your nearest Horizon Hobby customer service center for assistance. REVERSE POLARITY Make sure each connection polarity is correct between the power source and the charger, then between the charger and the battery CONNECTION BREAK Make sure the power connections are correct for charging SHORT ERR Make sure there are no short circuits between the poles of the battery or the battery and the charger. Replace damaged wires. INPUT VOL ERR Input voltage to the charger fell below the default or adjusted input voltage setting. Make sure the power source for the charger provides correct input voltage. VOL SELECT ERR Incorrect setting for cell in series count (pack voltage) of a lithium battery. Make charger settings match the battery pack label cell in series count specifications or replace the battery. BREAK DOWN Charger electronics require repair. BATTERY CHECK LOW VOLTAGE Battery voltage is lower than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery. BATTERY CHECK HIGH VOLTAGE Battery voltage is higher than the value setting in the charger. Adjust settings, then make sure the battery is not damaged or replace the battery. Battery Type Standard voltage (Volts per cell) Max. voltage (Volts per cell) Min. voltage (Volts per cell) Li-Po 3.70 4.20 3.00 Li-Io 3.60 4.10 3.00 Li-Fe 3.30 3.60 2.00 Ni-MH 1.20 1.60 1.00 Ni-Cd 1.20 1.60 0.85 Pb 2.00 2.45 1.75 1 YEAR LIMITED WARRANTY What this Warranty Covers - Horizon Hobby, Inc., (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship for a period of 1 years from the date of purchase. What is Not Covered - This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations. OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE. Purchaser’s Remedy - Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY. Limitation of Liability - HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase. Law - These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice. WARRANTY SERVICES Questions, Assistance, and Services - Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call 877.504.0233 toll free to speak to a Product Support representative. Inspection or Services - If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http:// www.horizonhobby.com/content/_service-center_render-servicecenter. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton. NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office. Warranty Requirements - For Warranty consideration, you must include your original sales receipt verifying the proofof-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon. Non-Warranty Service - Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/ content/_service-center_render-service-center. NOTICE: Horizon service is limited to Product compliant in the country of use and ownership. If non-compliant product is received by Horizon for service, it will be returned unserviced at the sole expense of the purchaser. Warranty and Service Contact Information Country of Purchase Horizon Hobby United States of America Horizon Service Center (Electronics and engines) Horizon Product Support (All other products) Address Phone Number/Email Address 4105 Fieldstone Rd Champaign, Illinois, 61822 USA 877-504-0233 Online Repair Request: visit www.horizonhobby.com/service 877-504-0233 [email protected] United Kingdom Horizon Hobby Limited Units 1-4 , Ployters Rd, Staple Tye, Harlow, Essex, CM18 7NS United Kingdom +44 (0) 1279 641 097 [email protected] Germany Horizon Technischer Service Christian-Junge-Straße 1 25337 Elmshorn, Germany +49 (0) 4121 2655 100 [email protected] France Horizon Hobby SAS 11 Rue Georges Charpak 77127 Lieusaint, France +33 (0) 1 60 18 34 90 [email protected] Garantie und Service Informationen Garantiezeitraum - Exklusive Garantie Horizon Hobby Inc (Horizon) garantiert, dass das gekaufte Produkt frei von Material- und Montagefehlern ist. Der Garantiezeitraum entspricht den gesetzlichen Bestimmung des Landes, in dem das Produkt erworben wurde. In Deutschland beträgt der Garantiezeitraum 6 Monate und der Gewährleistungszeitraum 18 Monate nach dem Garantiezeitraum. Einschränkungen der Garantie - (a) Die Garantie wird nur dem Erstkäufer (Käufer) gewährt und kann nicht übertragen werden. Der Anspruch des Käufers besteht in der Reparatur oder dem Tausch im Rahmen dieser Garantie. Die Garantie erstreckt sich ausschließlich auf Produkte, die bei einem autorisierten Horizon Händler erworben wurden. Verkäufe an dritte werden von dieser Garantie nicht gedeckt. Garantieansprüche werden nur angenommen, wenn ein gültiger Kaufnachweis erbracht wird. Horizon behält sich das Recht vor, diese Garantiebestimmungen ohne Ankündigung zu ändern oder modifizieren und widerruft dann bestehende Garantiebestimmungen. (b) Horizon übernimmt keine Garantie für die Verkaufbarkeit des Produktes, die Fähigkeiten und die Fitness des Verbrauchers für einen bestimmten Einsatzzweck des Produktes. Der Käufer allein ist dafür verantwortlich, zu prüfen, ob das Produkt seinen Fähigkeiten und dem vorgesehenen Einsatzzweck entspricht. (c) Ansprüche des Käufers Es liegt ausschließlich im Ermessen von Horizon, ob das Produkt, bei dem ein Garantiefall festgestellt wurde, repariert oder ausgetauscht wird. Dies sind die exklusiven Ansprüche des Käufers, wenn ein Defekt festgestellt wird. Horizon behält sich vor, alle eingesetzten Komponenten zu prüfen, die in den Garantiefall einbezogen werden können. Die Entscheidung zur Reparatur oder zum Austausch liegt nur bei Horizon. Die Garantie schließt kosmetische Defekte oder Defekte, hervorgerufen durch höhere Gewalt, falsche Behandlung des Produktes, falscher Einsatz des Produktes, kommerziellen Einsatz oder Modifikationen irgendwelcher Art aus. Die Garantie schließt Schäden, die durch falschen Einbau, falsche Handhabung, Unfälle, Betrieb, Service oder Reparaturversuche, die nicht von Horizon ausgeführt wurden aus. Rücksendungen durch den Käufer direkt an Horizon oder eine seiner Landesvertretung bedürfen der Schriftform. Schadensbeschränkung - Horizon ist nicht für direkte oder indirekte Folgeschäden, Einkommensausfälle oder kommerzielle Verluste, die in irgendeinem Zusammenhang mit dem Produkt stehen verantwortlich, unabhängig ab ein Anspruch im Zusammenhang mit einem Vertrag, der Garantie oder der Gewährleistung erhoben werden. Horizon wird darüber hinaus keine Ansprüche aus einem Garantiefall akzeptieren, die über den individuellen Wert des Produktes hinaus gehen. Horizon hat keinen Einfluss auf den Einbau, die Verwendung oder die Wartung des Produktes oder etwaiger Produktkombinationen, die vom Käufer gewählt werden. Horizon übernimmt keine Garantie und akzeptiert keine Ansprüche für in der folge auftretende Verletzungen oder Beschädigungen. Mit der Verwendung und dem Einbau des Produktes akzeptiert der Käufer alle aufgeführten Garantiebestimmungen ohne Einschränkungen und Vorbehalte. Wenn Sie als Käufer nicht bereit sind, diese Bestimmungen im Zusammenhang mit der Benutzung des Produktes zu akzeptieren, werden Sie gebeten, dass Produkt in unbenutztem Zustand in der Originalverpackung vollständig bei dem Verkäufer zurückzugeben. Sicherheitshinweise - Dieses ist ein hochwertiges Hobby Produkt und kein Spielzeug. Es muss mit Vorsicht und Umsicht eingesetzt werden und erfordert einige mechanische wie auch mentale Fähigkeiten. Ein Versagen, das Produkt sicher und umsichtig zu betreiben kann zu Verletzungen von Lebewesen und Sachbeschädigungen erheblichen Ausmaßes führen. Dieses Produkt ist nicht für den Gebrauch durch Kinder ohne die Aufsicht eines Erziehungsberechtigten vorgesehen. Die Anleitung enthält Sicherheitshinweise und Vorschriften sowie Hinweise für die Wartung und den Betrieb des Produktes. Es ist unabdingbar, diese Hinweise vor der ersten Inbetriebnahme zu lesen und zu verstehen. Nur so kann der falsche Umgang verhindert und Unfälle mit Verletzungen und Beschädigungen vermieden werden. Fragen, Hilfe und Reparaturen - Ihr lokaler Fachhändler und die Verkaufstelle können eine Garantiebeurteilung ohne Rücksprache mit Horizon nicht durchführen. Dies gilt auch für Garantiereparaturen. Deshalb kontaktieren Sie in einem solchen Fall den Händler, der sich mit Horizon kurz schließen wird, um eine sachgerechte Entscheidung zu fällen, die Ihnen schnellst möglich hilft. Wartung und Reparatur - Muss Ihr Produkt gewartet oder repariert werden, wenden Sie sich entweder an Ihren Fachhändler oder direkt an Horizon. Rücksendungen/Reparaturen werden nur mit einer von Horizon vergebenen RMA Nummer bearbeitet. Diese Nummer erhalten Sie oder ihr Fachhändler vom technischen Service. Mehr Informationen dazu erhalten Sie im Serviceportal unter www. Horizonhobby.de oder telefonisch bei dem technischen Service von Horizon. Packen Sie das Produkt sorgfältig ein. Beachten Sie, dass der Originalkarton in der Regel nicht ausreicht, um beim Versand nicht beschädigt zu werden. Verwenden Sie einen Paketdienstleister mit einer Tracking Funktion und Versicherung, da Horizon bis zur Annahme keine Verantwortung für den Versand des Produktes übernimmt. Bitte legen Sie dem Produkt einen Kaufbeleg bei, sowie eine ausführliche Fehlerbeschreibung und eine Liste aller eingesendeten Einzelkomponenten. Weiterhin benötigen wir die vollständige Adresse, eine Telefonnummer für Rückfragen, sowie eine Email Adresse. Garantie und Reparaturen - Garantieanfragen werden nur bearbeitet, wenn ein Originalkaufbeleg von einem autorisierten Fachhändler beiliegt, aus dem der Käufer und das Kaufdatum hervorgeht. Sollte sich ein Garantiefall bestätigen wird das Produkt repariert oder ersetzt. Diese Entscheidung obliegt einzig Horizon Hobby. Kostenpflichtige Reparaturen - Liegt eine kostenpflichtige Reparatur vor, erstellen wir einen Kostenvoranschlag, den wir Ihrem Händler übermitteln. Die Reparatur wird erst vorgenommen, wenn wir die Freigabe des Händlers erhalten. Der Preis für die Reparatur ist bei Ihrem Händler zu entrichten. Bei kostenpflichtigen Reparaturen werden mindestens 30 Minuten Werkstattzeit und die Rückversandkosten in Rechnung gestellt. Sollten wir nach 90 Tagen keine Einverständniserklärung zur Reparatur vorliegen haben, behalten wir uns vor, das Produkt zu vernichten oder anderweitig zu verwerten. Achtung: Kostenpflichtige Reparaturen nehmen wir nur für Elektronik und Motoren vor. Mechanische Reparaturen, besonders bei Hubschraubern und RC-Cars sind extrem aufwendig und müssen deshalb vom Käufer selbst vorgenommen werden. Garantie und Service Kontaktinformationen Land des Kauf Horizon Hobby Adresse Telefon/Email Adresse Deutschland Horizon Technischer Service Christian-Junge-Straße 1 25337 Elmshorn, Germany +49 (0) 4121 2655 100 [email protected] Kundendienstinformationen Land des Kauf Horizon Hobby Adresse Telefon/Email Adresse Deutschland Horizon Hobby GmbH Christian-Junge-Straße 1 25337 Elmshorn, Germany +49 (0) 4121 2655 100 [email protected] Rechtliche Informationen für die Europäische Union Parts Contact Information Country of Purchase Horizon Hobby Address Phone Number/Email Address Sales 4105 Fieldstone Rd Champaign, Illinois, 61822 USA 800-338-4639 [email protected] United Kingdom Horizon Hobby Limited Units 1-4, Ployters Rd, Staple Tye Harlow, Essex, CM18 7NS United Kingdom +44 (0) 1279 641 097 [email protected] Germany Horizon Hobby GmbH Christian-Junge-Straße 1 25337 Elmshorn, Germany +49 (0) 4121 2655 100 [email protected] Horizon Hobby SAS 11 Rue Georges Charpak 77127 Lieusaint, France +33 (0) 1 60 18 34 90 [email protected] United States of America France FCC Information Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Compliance Information for the European Union Declaration of Conformity (in accordance with ISO/IEC 17050-1) No. HH2012101001 Product(s): Item Number(s): No. HH2012101001 Horizon Hobby GmbH Christian-Junge-Straße 1 D-25337 Elmshorn erklärt das Produkt: declares the product: DYN 200WX2 Multi Chemistry Dual AC/DC Battery Charger, DYN4300EU, DYN4300UK DYN 200WX2 Multi Chemistry Dual AC/DC Battery Charger, DYN4300EU, DYN4300UK den übrigen einschlägigen Bestimmungen des EMV-Richtlinie 2004/108/EC und LVD-Richtlinie 2006/95/EC. complies with the essential requirements of the EMC Directive 2004/108/EC and LVD Directive 2006/95/EC. Angewendete harmonisierte Normen: Harmonized standards applied: EN55022: 2010 EN55024: 2010 EN61000-3-2:2006+A1:2009+A2:2009 EN61000-3-3:2008 EN60335-1: 2002+A11:2004+A1:2004+A12:2006+A2:2006+A13:2008+A14:2010+A15:2011 EN60335-2-29:2004+A2:2010 DYN 200WX2 Multi Chemistry Dual AC/DC Battery Charger DYN4300EU, DYN4300UK The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European EMC Directive 2004/108/EC and LVD Directive 2006/95/EC: EN55022: 2010 EN55024: 2010 EN61000-3-2:2006+A1:2009+A2:2009 EN61000-3-3:2008 EN60335-1: 2002+A11:2004+A1:2004+A12:2006+A2:2006+A13:2008+A14:2010+A15:2011 EN60335-2-29:2004+A2:2010 Signed for and on behalf of: Horizon Hobby, Inc. Champaign, IL USA Oct 10, 2012 Konformitätserklärung laut Allgemeine Anforderungen (ISO/IEC 17050-1:2004, korrigierte Fassung 2007-06-15); Deutsche und Englische Fassung EN ISO/IEC 17050-1:2010 Declaration of conformity (in accordance with ISO/IEC 17050-1) Steven A. Hall Executive Vice President and Chief Operating Officer International Operations and Risk Management Horizon Hobby, Inc. Instructions for disposal of WEEE by users in the European Union This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product. Elmshorn 10.10.2012 Steven A. Hall Geschäftsführer Managing Director Birgit Schamuhn Geschäftsführerin Managing Director Horizon Hobby GmbH; Christian-Junge-Straße 1; D-25337 Elmshorn HR Pi: HRB 1909; UStlDNr,:DE812678792; STR.NR.L 1829812324 Geschäftsführer: Birgit Schamuhn, Steven A. Hall -- Tel.: +49 (0) 4121 2655 100 • Fax: +49 (0) 4121 2655 111 eMail: [email protected]; Internet: www.horizonhobby.de Es gelten unsere allgemeinen Geschäftsbedingungen, die in unseren Geschäftsräumen eingesehen weden können. Eare bleibt bis zur vollstandigen Bezahlung Eigentum der Horizon Hobby GmbH Anweisungen zur Entsorgung von Elektro—und Elektronik-Altgeräten für Benutzer in der Europäischen Union Dieses Produkt darf nicht zusammen mit anderem Abfall entsorgt werden. Stattdessen ist der Benutzer dafür verantwortlich, unbrauchbare Geräte durch Abgabe bei einer speziellen Sammelstelle für das Recycling von unbrauchbaren elektrischen und elektronischen Geräten zu entsorgen. Die separate Sammlung und das Recycling von unbrauchbaren Geräten zum Zeitpunkt der Entsorgung hilft, natürliche Ressourcen zu bewahren und sicherzustellen, dass Geräte auf eine Weise wiederverwertet werden, bei der die menschliche Gesundheit und die Umwelt geschützt werden. Weitere Informationen dazu, wo Sie unbrauchbare Geräte zum Recycling abgeben können, erhalten Sie bei lokalen Ämtern, bei der Müllabfuhr für Haushaltsmüll sowie dort, wo Sie das Produkt gekauft haben. Garantie et réparations Durée de la garantie - Garantie exclusive - Horizon Hobby, Inc. (Horizon) garantit que le Produit acheté (le « Produit ») sera exempt de défauts matériels et de fabrication à sa date d’achat par l’Acheteur. La durée de garantie correspond aux dispositions légales du pays dans lequel le produit a été acquis. La durée de garantie est de 6 mois et la durée d’obligation de garantie de 18 mois à l’expiration de la période de garantie. Limitations de la garantie - (a) La garantie est donnée à l’acheteur initial (« Acheteur ») et n’est pas transférable. Le recours de l’acheteur consiste en la réparation ou en l‘échange dans le cadre de cette garantie. La garantie s’applique uniquement aux produits achetés chez un revendeur Horizon agréé. Les ventes faites à des tiers ne sont pas couvertes par cette garantie. Les revendications en garantie seront acceptées sur fourniture d’une preuve d’achat valide uniquement. Horizon se réserve le droit de modifier les dispositions de la présente garantie sans avis préalable et révoque alors les dispositions de garantie existantes. (b) Horizon n’endosse aucune garantie quant à la vendabilité du produit ou aux capacités et à la forme physique de l’utilisateur pour une utilisation donnée du produit. Il est de la seule responsabilité de l’acheteur de vérifier si le produit correspond à ses capacités et à l’utilisation prévue. (c) Recours de l’acheteur – Il est de la seule discrétion d‘Horizon de déterminer si un produit présentant un cas de garantie sera réparé ou échangé. Ce sont là les recours exclusifs de l’acheteur lorsqu’un défaut est constaté. Horizon se réserve la possibilité de vérifier tous les éléments utilisés et susceptibles d’être intégrés dans le cas de garantie. La décision de réparer ou de remplacer le produit est du seul ressort d’Horizon. La garantie exclut les défauts esthétiques ou les défauts provoqués par des cas de force majeure, une manipulation incorrecte du produit, une utilisation incorrecte ou commerciale de ce dernier ou encore des modifications de quelque nature qu’elles soient. La garantie ne couvre pas les dégâts résultant d’un montage ou d’une manipulation erronés, d’accidents ou encore du fonctionnement ainsi que des tentatives d’entretien ou de réparation non effectuées par Horizon. Les retours effectués par le fait de l’acheteur directement à Horizon ou à l’une de ses représentations nationales requièrent une confirmation écrite. Limitation des dégâts - Horizon ne saurait être tenu pour responsable de dommages conséquents directs ou indirects, de pertes de revenus ou de pertes commerciales, liés de quelque manière que ce soit au produit et ce, indépendamment du fait qu’un recours puisse être formulé en relation avec un contrat, la garantie ou l’obligation de garantie. Par ailleurs, Horizon n’acceptera pas de recours issus d’un cas de garantie lorsque ces recours dépassent la valeur unitaire du produit. Horizon n’exerce aucune influence sur le montage, l’utilisation ou la maintenance du produit ou sur d’éventuelles combinaisons de produits choisies par l’acheteur. Horizon ne prend en compte aucune garantie et n‘accepte aucun recours pour les blessures ou les dommages pouvant en résulter. En utilisant et en montant le produit, l’acheteur accepte sans restriction ni réserve toutes les dispositions relatives à la garantie figurant dans le présent document. Si vous n’êtes pas prêt, en tant qu’acheteur, à accepter ces dispositions en relation avec l’utilisation du produit, nous vous demandons de restituer au vendeur le produit complet, non utilisé et dans son emballage d’origine. Indications relatives à la sécurité - Ceci est un produit de loisirs perfectionné et non un jouet. Il doit être utilisé avec précaution et bon sens et nécessite quelques aptitudes mécaniques ainsi que mentales. L’incapacité à utiliser le produit de manière sûre et raisonnable peut provoquer des blessures et des dégâts matériels conséquents. Ce produit n’est pas destiné à être utilisé par des enfants sans la surveillance par un tuteur. La notice d’utilisation contient des indications relatives à la sécurité ainsi que des indications concernant la maintenance et le fonctionnement du produit. Il est absolument indispensable de lire et de comprendre ces indications avant la première mise en service. C’est uniquement ainsi qu’il sera possible d’éviter une manipulation erronée et des accidents entraînant des blessures et des dégâts. Questions, assistance et réparations - Votre revendeur spécialisé local et le point de vente ne peuvent effectuer une estimation d’éligibilité à l’application de la garantie sans avoir consulté Horizon. Cela vaut également pour les réparations sous garantie. Vous voudrez bien, dans un tel cas, contacter le revendeur qui conviendra avec Horizon d’une décision appropriée, destinée à vous aider le plus rapidement possible. Maintenance et réparation - Si votre produit doit faire l’objet d’une maintenance ou d‘une réparation, adressez-vous soit à votre revendeur spécialisé, soit directement à Horizon. Emballez le produit soigneusement. Veuillez noter que le carton d‘emballage d’origine ne suffit pas, en règle générale, à protéger le produit des dégâts pouvant survenir pendant le transport. Faites appel à un service de messagerie proposant une fonction de suivi et une assurance, puisque Horizon ne prend aucune responsabilité pour l’expédition du produit jusqu’à sa réception acceptée. Veuillez joindre une preuve d’achat, une description détaillée des défauts ainsi qu’une liste de tous les éléments distincts envoyés. Nous avons de plus besoin d’une adresse complète, d’un numéro de téléphone (pour demander des renseignements) et d’une adresse de courriel. Garantie et réparations - Les demandes en garantie seront uniquement traitées en présence d’une preuve d’achat originale émanant d’un revendeur spécialisé agréé, sur laquelle figurent le nom de l’acheteur ainsi que la date d’achat. Si le cas de garantie est confirmé, le produit sera réparé Cette décision relève uniquement de Horizon Hobby. Réparations payantes - En cas de réparation payante, nous établissons un devis que nous transmettons à votre revendeur. La réparation sera seulement effectuée après que nous ayons reçu la confirmation du revendeur. Le prix de la réparation devra être acquitté au revendeur. Pour les réparations payantes, nous facturons au minimum 30 minutes de travail en atelier ainsi que les frais de réexpédition. En l’absence d’un accord pour la réparation dans un délai de 90 jours, nous nous réservons la possibilité de détruire le produit ou de l’utiliser autrement. Attention: Nous n’effectuons de réparations payantes que pour les composants électroniques et les moteurs. Les réparations touchant à la mécanique, en particulier celles des hélicoptères et des voitures radiocommandées, sont extrêmement coûteuses et doivent par conséquent être effectuées par l’acheteur lui-même. Coordonnées de Garantie et réparations Durata della Garanzia Periodo di garanzia - Garanzia esclusiva - Horizon Hobby, Inc., (Horizon) garantisce che i prodotti acquistati (il “Prodotto”) sono privi di difetti relativi ai materiali e di eventuali errori di montaggio. Il periodo di garanzia è conforme alle disposizioni legali del paese nel quale il prodotto è stato acquistato. Tale periodo di garanzia ammonta a 6 mesi e si estende ad altri 18 mesi dopo tale termine. Limiti della garanzia - (a) La garanzia è limitata all’acquirente originale (Acquirente) e non è cedibile a terzi. L’acquirente ha il diritto a far riparare o a far sostituire la merce durante il periodo di questa garanzia. La garanzia copre solo quei prodotti acquistati presso un rivenditore autorizzato Horizon. Altre transazioni di terze parti non sono coperte da questa garanzia. La prova di acquisto è necessaria per far valere il diritto di garanzia. Inoltre, Horizon si riserva il diritto di cambiare o modificare i termini di questa garanzia senza alcun preavviso e di escludere tutte le altre garanzie già esistenti. (b) Horizon non si assume alcuna garanzia per la disponibilità del prodotto, per l’adeguatezza o l’idoneità del prodotto a particolari previsti dall’utente. è sola responsabilità dell’acquirente il fatto di verificare se il prodotto è adatto agli scopi da lui previsti. (c) Richiesta dell’acquirente – spetta soltanto a Horizon, a propria discrezione riparare o sostituire qualsiasi prodotto considerato difettoso e che rientra nei termini di garanzia. queste sono le uniche rivalse a cui l’acquirente si può appellare, se un prodotto è difettoso. Horizon si riserva il diritto di controllare qualsiasi componente utilizzato che viene coinvolto nella rivalsa di garanzia. Le decisioni relative alla sostituzione o alla riparazione avvengono solo in base alla discrezione di Horizon. Questa garanzia non copre dei danni superficiali o danni per cause di forza maggiore, uso errato del prodotto, negligenza, uso ai fini commerciali, o una qualsiasi modifica a qualsiasi parte del prodotto. Questa garanzia non copre danni dovuti ad una installazione errata, ad un funzionamento errato, ad una manutenzione o un tentativo di riparazione non idonei a cura di soggetti diversi da Horizon. La restituzione del prodotto a cura dell’acquirente, o da un suo rappresentante, deve essere approvata per iscritto dalla Horizon. Limiti di danno - Horizon non si riterrà responsabile per danni speciali, diretti, indiretti o consequenziali; perdita di profitto o di produzione; perdita commerciale connessa al prodotto, indipendentemente dal fatto che la richiesta si basa su un contratto o sulla garanzia. Inoltre la responsabilità di Horizon non supera mai in nessun caso il prezzo di acquisto del prodotto per il quale si chiede la responsabilità. Horizon non ha alcun controllo sul montaggio, sull’utilizzo o sulla manutenzione del prodotto o di combinazioni di vari prodotti. Quindi Horizon non accetta nessuna responsabilità per danni o lesioni derivanti da tali circostanze. Con l’utilizzo e il montaggio del prodotto l’utente acconsente a tutte le condizioni, limitazioni e riserve di garanzia citate in questa sede. Qualora l’utente non fosse pronto ad assumersi tale responsabilità associata all’uso del prodotto, si suggerisce di di restituire il prodotto intatto, mai usato e immediatamente presso il venditore. Indicazioni di sicurezza - Questo è un prodotto sofisticato di hobbistica e non è un giocattolo. Esso deve essere manipolato con cautela, con giudizio e richiede delle conoscenze basilari di meccanica e delle facoltà mentali di base. Se il prodotto non verrà manipolato in maniera sicura e responsabile potrebbero risultare delle lesioni, dei gravi danni a persone, al prodotto o all’ambiente circostante. Questo prodotto non è concepito per essere usato dai bambini senza una diretta supervisione di un adulto. Il manuale del prodotto contiene le istruzioni di sicurezza, di funzionamento e di manutenzione del prodotto stesso. È fondamentale leggere e seguire tutte le istruzioni e le avvertenze nel manuale prima di mettere in funzione il prodotto. Solo così si eviterà un utilizzo errato e di preverranno incidenti, lesioni o danni. Domande, assistenza e riparazioni - Il vostro negozio locale e/o luogo di acquisto non possono fornire garanzie di assistenza o riparazione senza previo colloquio con Horizon. questo vale anche per le riparazioni in garanzia. Quindi in tale casi bisogna interpellare un rivenditore, che si metterà in contatto subito con Horizon per prendere una decisione che vi possa aiutare nel più breve tempo possibile. Manutenzione e riparazione - Se il prodotto deve essere ispezionato o riparato, si prega di rivolgersi ad un rivenditore specializzato o direttamente ad Horizon. il prodotto deve essere Imballato con cura. Bisogna far notare che i box originali solitamente non sono adatti per effettuare una spedizione senza subire alcun danno. Bisogna effettuare una spedizione via corriere che fornisce una tracciabilità e un’assicurazione, in quanto Horizon non si assume alcuna responsabilità in relazione alla spedizione del prodotto. Inserire il prodotto in una busta assieme ad una descrizione dettagliata degli errori e ad una lista di tutti i singoli componenti spediti. Inoltre abbiasmo bisogno di un indirizzo completo, di un numnero di telefono per chiedere ulteriori domande e di un indirizzo e-mail. Garanzia a riparazione - Le richieste in garanzia verranno elaborate solo se è presente una prova d’acquisto in originale proveniente da un rivenditore specializzato autorizzato, nella quale è ben visibile la data di acquisto. Se la garanzia viene confermata, allora il prodotto verrà riparato o sostituito. Questa decisione spetta esclusivamente a Horizon Hobby. Riparazioni a pagamento - Se bisogna effettuare una riparazione a pagamento, effettueremo un preventivo che verrà inoltrato al vostro rivenditore. La riparazione verrà effettuata dopo l’autorizzazione da parte del vostro rivenditore. La somma per la riparazione dovrà essere pagata al vostro rivenditore. Le riparazioni a pagamento avranno un costo minimo di 30 minuti di lavoro e in fattura includeranno le spese di restituzione. Qualsiasi riparazione non pagata e non richiesta entro 90 giorni verrà considerata abbandonata e verrà gestita di conseguenza. ATTENZIONE: Le riparazioni a pagamento sono disponibili solo sull’elettronica e sui motori. Le riparazioni a livello meccanico, soprattutto per gli elicotteri e le vetture RC sono molto costose e devono essere effettuate autonomamente dall’acquirente. Garanzia e Revisiona informazioni per i contatti Stato de acquistato Horizon Hobby Indirizzo Telefono/Indirizzo e-mail Germania Horizon Technischer Service Christian-Junge-Straße 1 25337 Elmshorn, Germany +49 (0) 4121 2655 100 [email protected] Informazioni di Servizio clienti Pays d’achat Horizon Hobby Adresse Numéro de téléphone/Courriel Stato de acquistato Horizon Hobby Indirizzo Telefono/Indirizzo e-mail France Horizon Hobby SAS 11 Rue Georges Charpak 77127 Lieusaint, France +33 (0) 1 60 18 34 90 [email protected] Germania Horizon Hobby GmbH Christian-Junge-Straße 1 25337 Elmshorn, Germany +49 (0) 4121 2655 100 [email protected] Informations de contact pour les pièces Informazioni sulla conformità per l’Unione Europea Pays d’achat Horizon Hobby Adresse Numéro de téléphone/Courriel France Horizon Hobby SAS 11 Rue Georges Charpak 77127 Lieusaint, France +33 (0) 1 60 18 34 90 [email protected] Informations de conformité pour l’Union européenne Déclaration de conformité (conformément à la norme ISO/IEC 17050-1) No. HH2012101001 Prodotto(i): Numero(i) articolo: DYN 200WX2 Multi Chemistry Dual AC/DC Battery Charger DYN4300EU, DYN4300UK Gli oggetti presentati nella dichiarazione sopra citata sono conformi ai requisiti delle specifiche elencate qui di seguito, seguendo le disposizioni della direttiva europea EMC 2004/108/EC e LVD 2006/95/EC: No. HH2012101001 Produit(s): Numéro(s) d’article: Dichiarazione di conformità (in conformità con ISO/IEC 17050-1) DYN 200WX2 Multi Chemistry Dual AC/DC Battery Charger DYN4300EU, DYN4300UK EN55022: 2010 EN55024: 2010 L’objet de la déclaration décrit ci-dessus est en conformité avec les exigences des spécifications énumérées ci-après, suivant les conditions de la directive CEM 2004/108/EC et LVD 2006/95/EC: EN61000-3-2:2006+A1:2009+A2:2009 EN61000-3-3:2008 EN55022: 2010 EN55024: 2010 EN60335-1: 2002+A11:2004+A1:2004+A12:2006+A2:2006+A13:2008+A14:2010+A15:2011 EN60335-2-29:2004+A2:2010 EN61000-3-2:2006+A1:2009+A2:2009 EN61000-3-3:2008 Firmato per conto di: EN60335-1: 2002+A11:2004+A1:2004+A12:2006+A2:2006+A13:2008+A14:2010+A15:2011 EN60335-2-29:2004+A2:2010 Signé en nom et pour le compte de: Horizon Hobby, Inc. Champaign, IL USA 10.10.2012 Steven A. Hall Vice-Président, Directeur Général Gestion Internationale des Activités et des Risques Horizon Hobby, Inc. Elimination dans l’Union Européenne Ce produit ne doit pas être éliminé avec les ordures ménagères. Il est de la responsabilité de l‘utilisateur de remettre le produit à un point de collecte officiel des déchets d’équipements électriques. Cette procédure permet de garantir le respect de l’environnement et l’absence de sollicitation excessive des ressources naturelles. Elle protège de plus le bien-être de la communauté humaine. Pour plus d’informations quant aux lieux d’éliminations des déchets d‘équipements électriques, vous pouvez contacter votre mairie ou le service local de traitement des ordures ménagères. Horizon Hobby, Inc. Champaign, IL USA 10.10.2012 Steven A. Hall Executive Vice President and Chief Operating Officer International Operations and Risk Management Horizon Hobby, Inc. Istruzioni del RAEE per lo smaltimento da parte di utenti dell’Unione Europea Questo prodotto non deve essere smaltito assieme ai rifiuti domestici. Al contrario, l’utente è responsabile dello smaltimento di tali rifiuti che devono essere portati in un centro di raccolta designato per il riciclaggio di rifiuti elettrici e apparecchiature elettroniche. La raccolta differenziata e il riciclaggio di tali rifiuti provenienti da apparecchiature nel momento dello smaltimento aiuteranno a preservare le risorse naturali e garantiranno un riciclaggio adatto a proteggere il benessere dell’uomo e dell’ambiente. Per maggiori informazioni sui centri di raccolta, contattare il proprio ufficio locale, il servizio di smaltimento rifiuti o il negozio presso il quale è stato acquistato il prodotto. ©2012 Horizon Hobby Inc. Dynamite, Passport, EC3 and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, Inc. iPhone and iPod are trademarks of Apple, Inc., registered in the U.S. and other countries. Microsoft®, Windows XP® and Windows Vista® are registered trademarks of the Microsoft Corporation. Created 09/12 32772