IP Link® Device Interface Ethernet Communication Sheet

IP Link® Device Interface
Ethernet Communication Sheet
bose_25_4511_11.pkn
Revision: 1/13/2015
This document provides additional assistance with wiring your Extron IP Link enabled product to your device.
Different components may require a different wiring scheme than those listed below.
For complete operating instructions, refer to the user’s manual for the specific Extron IP Link enabled product or
the controlled device manufacturer supplied documentation.
Device Specifications:
Device Type:
Manufacturer:
Firmware Version:
Model(s):
Audio Processor
Bose
V4.100
ControlSpace ESP-88, ControlSpace ESP-00
Minimum Software and Firmware Requirements:
IP Link
Compiler
IP Link
Firmware
1.6.0
1.17
GC Version
3.5.1
Version History:
Driver
Version
Date
11
1/13/2015
Added Tie and Untie commands.
9
2/6/2014
Extron Certified. Added model ControlSpace ESP-00.
8
8/20/2013
Extron Certified. Tested on ControlSpace ESP-88.
7
5/17/2013
Added 16 gain blocks that are configurable to the unit's software. This is recommended by
the manufacturer.
6
4/30/2013
Remove Input and Output functionality. Modify driver to contain 32 groups.
5
01/16/2013
Added Input and Output functionality. Added Group Level
Step commands. Remove Preset recall since it is not supported by new firmware. Added
Parameter Recall command. Brought driver to most current A/V Standards.
4
6/21/2012
Added 9 control groups A-I. Added 8 more Input Slots.
2
4/5/2011
Extron Certified. Tested on ControlSpace ESP-88. Updated driver to new standards. Added
None status to Preset. Fixed parsing for status.
1
9/2/2010
Initial version.
Notes
Page 1 of 3
bose_25_4511_11.pkn
IP Link® Device Interface
Ethernet Communication Sheet
Revision: 1/13/2015
Driver Notes:
 Device needs to have firmware v.3 or later.
 This driver includes Volume Optimization.
 When a Tie has been made between an Input and Output, you can later review the tie by clicking on the
Output number button to highlight the Input number button to which it is tied.
Control Commands & States:
Gain 1-16
-60 to 12 in steps of 1
Gain 1-16 Mute
On
Group 1 – 32 Volume (Step)
1–8
Group 1 – 32 Volume (Discrete)
0 to 144 in steps of 1
Group 1 – 32 Mute
On
Input
1 – 16
Output
1 – 16
Parameter Recall
1 – 255
Tie Control
Tie
Untie
Connection Status
Connected
Disconnected
Gain 1-16
-60 to 12 in steps of 1
Gain 1-16 Mute
On
Group 1 – 32 Volume (Discrete)
0 to 144 in steps of 1
Group 1 – 32 Mute
On
Parameter Recall
1 – 255
Off
Toggle
Off
Toggle
Status Available:
Off
Off
Page 2 of 3
IP Link® Device Interface
Ethernet Communication Sheet
bose_25_4511_11.pkn
Revision: 1/13/2015
Network communication:
When configuring the Ethernet driver, be sure device settings match that of the GC configuration.
Connection will be lost when uploading or downloading from the ESP from the ControlSpace Designer software.
Port Type:
Ethernet
Logon Credentials
Supported:
Default Port:
No
Multi-Connection
Capable:
Port Changeable:
No
10055
Yes
Ethernet Driver Configuration Description:
Please refer to user manual for settings and changes to the network communication parameters.
Notes for the Device:
When Network cable is disconnected the unit must be power cycled to get the network connection to reconnect. This
can be done by physically turning off the device, unplugging the power connector, and then plugging the power
connector back in.
Page 3 of 3