NIAB 5 – 15 C

INSTRUCTION BOOK
NIAB
SERVICE AND SPARE PARTS
NIAB 5 – 15 C
Index:
•
•
•
•
•
•
•
Technical information
……………………………………………………………………..
1
General technical description
…………………………………………………………….
2
Starting instructions
……………………………………………………………………….
3
Operating instructions
…………………………………………………………………….
4
Maintenance
……………………………………………………………………………….
6
Safety instructions
…………………………………………………………………………
7
Index of part list
……………………………………………………………………………
8
Note! Read carefully through the security instructions before that any
action is taking place with the machine.
Product description:
NIAB 5 – 15 is a stroke fed processor that is intended to be used together with a three – point
linkage on an agricultural tractor. The machine is driven by the tractors PTO system. The input
voltage to the electric system is connected to the trailer socket. The method entails that manually
felled trees are winched in to the machine with a radio – guided winch. The trees are handled and
processed with the combined griffin – and delimbing aggregate and are adapted by the built – in
saw. The machines movement zone admits sorting of lumber in to separate piles.
© 2003 FORS MW Ltd
www.forsmw.com
i
NIAB 5 – 15 C
Technical data
Width
Height
Length
Weight
Chain bar
Saw capacity
Chain partition
Chain speed
Working angle
Length winch wire
Diameter winch wire
Max. Pulling power hydraulic winch
Max. Lumber diameter
Stroke length stroke feeder
Average speed stroke feeder
Delimbing pressure
Nominal hydraulic oil flow
Nominal PTO speed
Power need
Volume hydraulic oil tank
Electrical provision
Type of oil – Hydraulic oil
Type of oil – Gearbox
2,45 m
2,3 m
2m
1050 kg
18”
18/25 kW/hk
0,404”
40 m/sec
75°
40 m
8 mm
2,5 ton
500 mm
1520 mm
1,3 m/sec
11/110 Mpa/bar
60 l/min
400 r/min
30/ 40 kW/ hk
65 l
12 V – 6 A
32
Hypoid oil 80/90 0,4 l
www.forsmw.com
1
NIAB 5 – 15 C
General technical description
The NIAB 5 – 15 processor operates via a hydraulic pump with a gearbox connected to the tractors
PTO system. The hydraulic oil from the pump travels directly to a valve chest situated under cover
above the operating lever control panel. The operating lever control panel can bed adjusted to a
comfortable working position, raised by lifting the control panel and lowered by pressing down the
rod going through the control panel.
The valve chest inlet section has a relief valve that ensures maximum pressure to the differing
functions. A pressure gauge connection is fitted for testing the main pressure.
The first section of the valve chest feeds both the saw as well as the winch with pressure oil. The
winch position has a locking device, when this first section is engaged all other functions are
cancelled out. Oil from the valve chest and limbing control valve travel via a filter back to the
tank.
The height of the levers can be adjusted by lifting the lever console. To lower it, press the strut –
ends on the side of the lever console.
The limbing pressure control valve contains valves for the use of differential operation, which
means that then the boom extension goes out the oil goes from the minus side to the plus side,
which increases the speed of the cylinder. Further one there are equal valves to release the oil from
the plus side directly to the tank (the flow duplicates).
An electrical maneuvered tree way direction valve directs the pressure to the limbing knives, so
that either the cylinder works with the full potential of the piston area or only the rod area. This is
done so that you can receive both the retract force as well as limbing - pressure. A pilot steered
tree way valve controls the chain saw cylinder. The spring camber of the valve is used as a grease
pump.
www.forsmw.com
2
NIAB 5 – 15 C
Further on the limbing pressure control valve contains a smother to build up the pressure towards
the saw cylinder as well as a tap that can be opened to be able to fade the sword manually.
Within the frame at the front edge there is situated a valve plate holding a pressure reducing valve
and also an electrical manoeuvred direction valve for the manoeuvring of the saw and winch valve.
The pressure reducing valve supplies the direction valve and the measuring wheel cylinder with a
pressure of 25 bar. At the same location at the front edge of the frame is also situated the valve
plate that steers the automatic function.
The winch is driven directly by a hydraulic engine that will disconnect then it’s not under pressure.
The electrical direction valve is mounted directly on the winch engine. To receive oil for the winch
you press the saw - lever forward until locked position.
Enclosed you will find separate descriptions of the different hydraulic functions, the digital length
– and diameter meter and electric and hydraulic circuits.
Notice! The lever will work as an emergency stop
Description of length measure
Within the measuring wheel (1) is mounted a slotted disc (3). The slotted disc rotates inside the
optical read sensing (2). The read sensing registers pulse and direction that are forwarded to the
display, which convert this data to cm. One rotation on the measuring wheel correspond to 48 cm.
The plug (4) is intended for mounting of the slotted disc and also for inspecting and realise
condensate, which can originate high air humidity in combination of temperature variations and
cause wrongful measuring result.
www.forsmw.com
3
NIAB 5 – 15 C
Instruction for calibration of diameter measuring
To obtain the optimal accurse the calibration should take place every time the actual dimension is
changed. The optimal accurse is obtained if one measures two diameters, one lower limit and one
present upper limit for example if the assortment limit is situated at 16 cm one calibrates on 10 and
20 cm. Another reason for calibrating is when one changes the felling of trees, when the measuring
point and the gap are situated around 1 m from each other and in which the taper off can vary in
different sorts of areas.
Programming
The manovering panel is equipped with 13 different menus’ that all activates through the menu
tangent. On the lower display the actual menu is presented. The upper display shows the present
value which can be altered with + or – when needed.
The menus´1 – 9 are intended for pre - selection lengths. For manoeuvring, approach as follows;
-
Push the menu button so that number one occurs and starts to flash.
Thereafter set the length of your wishes by pressuring + or -. For example, for three meter
the number 300 should be displayed in the upper display window.
Then push the second number and number two starts to flash.
Proceed as presented above for number one.
Continue like this until all of the nine pre - selections are done.
Menu number ten is the setting for the length measuring and it shall be at 500. (Note! – Earlier
250)
Diameter setting
Menu 11: Calibration point 1 for diameter setting.
- The grippers shall be closed for the lesser calibration diameter. Measure the diameter directly at
the intended place of cutting and choose the right value at the display with the help of + and –
tangents.
www.forsmw.com
4
NIAB 5 – 15 C
Menu 12: Calibration point 2 for diameter setting.
- The grippers shall be closed for the major calibration diameter. Measure the diameter directly at
the intended place of cutting and choose the right value at the display with the help of + and –
tangents.
Menu 13: This menu is an offset value to eliminate the brake distance.
- If one for example programmes 10 cm. That will activate the stop 10 cm before marking
for cross cutting.
- To end the programme push the menu button until menu 13 has passed. That sets you
forwarded to working position.
- If you by accident would touch the menu button there is no other choice then to push the
menu button until number 13 has passed.
- To choose pre – programmed marking for cross cutting use the + or – buttons. Press start
and the saw is ready.
Starting instructions
IMPORTENT – Read before operating processor
Before operating check following:
 That the processor is securely attached to the tractor, ALWAYS use the safety chain, along
with the top link.
 PTO connection
 Lack of restricting obstructions to the tractor.
 See to condition and adjustment of limbing arm rollers
 Tension and cutting edge of chain
 Fold up the parking supports. (Remove the red transport bracket)
In cold weather the hydraulic system needs to be warmed up prior to starting operations. All
functions of the processor should be tested including the winch; the oily supply lever can be used
emergency switch – off.
www.forsmw.com
5
NIAB 5 – 15 C
Operating instruction
The NIAB 5 – 15 tractor-mounted processor is easily employed for work on extraction tracks the
tractor can reverse along the track.
When in operation, the tractor and processor should be placed on the same level so as to avoid
unnecessary strain on the tractors three-point linkage.
Winching:
The process is dangerous unless the following points are adhered to:
 When winching, the limbing head should be placed on the ground beside the tractors rear
wheel.
 Reduce the pulling power of the winch by easing the knob on the side of winch valve. The
pulling power can thereafter be adjusted according to the stability of the tractor.
 Move control lever for the winch forward to locking position. This activates the oil to the
winch hydraulics (this lever can also be used as an emergency switch).
 Pick up the timber hook and release the winch rope arm from its parked position and
approach the tree to be winched in.
Damage Hazard!
Before starting to connect the wire to the tree it is important that sufficient wire is pulled out, so
that the connection can be completed without having to stretch the wire.
If the wire is loosely wound up on the drum it can be withdrawn in – between intermediate turns
and get stuck there, with the consequence that the wire begins to pull when fed. If the wire is then
slack, the arm fall down and the winch stops, if the wire however is tense the winch continues to
pull. To stop it push in the transmitting button until the wire is slack and the arm is down. Then the
winch can be stopped and the wire can be corrected.
To avoid problems with loosely wound wire it is important to;
www.forsmw.com
6
NIAB 5 – 15 C
 Never lift the steering arm except by pulling the wire,
 Have the wire-feeding valve correctly adjusted so that wire is not fed out when the arm is
not lifted,
 Winch a tree from the distance once in a while so that almost the entire wire is used.
When the whole wire is been pulled out it comes loose from the cord drum. NOTE that this is a
security function. It is only to reattach the wire loop on the drum again.
Attach the wire rope to the butt end of the tree. It is possible to winch than one tree at the same
time. Activate the remote control to commence winching. Always walk behind the tree being
winched in. Stop the process once the tree comes inside the working area the processor.
Release the wire rope and recoil leaving, approximately 50 centimetres out. Place the winch
control lever in its neutral position before replacing the winch rope arm in its parked position.
Once inside the processors working area, the left hand button can operate the winch on the controls
lever panel instead of using the remote control.
Grab the tree with the limbing knives and pull the tree to the clamp. There are two systems of
switching to limbing low pressure to choose from.
1. The process is operated with the limbing lever on the control panel. Limbing pressure is
engaged when the limbing arm is going out and the high pressure is engaged when the
limbing arm is pulled in.
2. Limbing pressure is engaged manually by pressing down on the knob of the limbing arm
lever. The later method is to be prepared when dealing with thick and awkward branch.
The choice between the two systems is made possible by the right hand button on the control lever
panel. A light on the limbing pressure control valve will light up when limbing low pressure is
engaged.
Limbing is performed with the left hand operating the turn and tilt levers and the right hand on the
limbing arm and clamp levers. The limbing arm has a stroke length of 1,52 meters. The end of the
stroke is fitted with a damper, which reduces the speed towards the end of the stroke to protect the
machine. It is possible to judge the length of timber to be cut by the length of the limbing stroke.
Fore a more accurate cut, use the electronic measuring device.
Lay down butt end to prevent splitting when sawing, move the saw lever smoothly fully
backwards. Check that the saw ram is fully retracted before recommencing limbing. Withdrawing
the lever using delimbing head will loop off the treetops. Brash and debris can be pushed out of the
way by using the limbing head.
When using the automatic system the basics are the same all for one difference that the processor
can move by itself into pre - choice length. This is handled accordingly;
www.forsmw.com
7
NIAB 5 – 15 C
Choose length (for programming se page * ) with the + or – buttons, press start or simply start the
saw to start the sequence, press the right button on the boom extension lever at the same time as
the lever is pulled forwards. This will move the processor to pre- selected length. When it stops,
push the saw button and start to cut. If the same length shall be cut again keep the grip on the
boom extension lever, this will keep the processor moving after the cut has been made. If the
setting manual marking for cross cutting has been chosen, with the tilt switch on the manoeuvring
box, the processor will work until the boom extension lever is realised or the sawing button will be
pressed. The method can be used on different lengths. In normal circumstances the machines starts
when the boom extension is on its way out however if the machine has been stopped in outer
position the machine might start to work its way inwards. Note! Then you need to be observant
and look for so that the sward had time to go up.
The grippers contact diameter when retracting is adjusted with the wheel on the bottom of the
valve automatic block.
Maintenance
Daily checks:







Wear on hoses
Oil leaks
Wear and tear of saw chain and bar
Condition of rollers of the limbing head
Wire rope wear and tear
PTO attachment
Grease all moving parts daily, twice daily in hot weather
Every 30 hours:





Tighten bolts cover plate winch 90 Nm
Tighten bolts winch motor 45 Nm
Thorough greasing, oiling and slearing
Tighten loose pipes and attachments
With fully extend limbing arm, clean and apply a thin layer of grease on the roller lanes.
After 250 hours:
 Change return filter after 250 h or once a year
 Change oil gearbox (hypoid oil 80/90 0,4l)
www.forsmw.com
8
NIAB 5 – 15 C
Safety Precautions
IMPORTENT – Never use the NIAB 5 – 15 unless the tractor three – point linkage and top link
are in perfect working order.
 Always use the safety chain in conjunction with the top link.
 Ensure that the gearbox and oil pump are securely fastened to the tractor. Check the
gearbox and oil pump for leaks. If shaft extension is used, it should be properly fitted and
secured to the PTO shaft.
 Always fold up the parking support when the machine is in use.
 Always use the boom as a support when winching.
 Release sufficient wire rope to prevent stretching, when attaching the tree.
 Never use a worn wire rope.
 Always walk behind the tree being winched in.
 Adjust the pulling power of winch in accordance with the stability of the tractor.
 During delimbing the operator must remain behind the operating control panel. It is
forbidden to reach across the delimbing boom when the processor is working.
 When in transit or stationary the delimbing head should remain in its upper front position.
 It is forbidden to perform reparations or adjustments on the machine with PTO running.
Keep people outside the 15 meters operational area of the processor.
www.forsmw.com
9
NIAB 5 – 15 C
Index of part list
•
Boom
•
Turning bracket
•
Winch
•
Joystick carrier
•
Length meter
•
Boom & delimbing arm
•
Delimbing arm
•
Tank
•
Saw
•
Valve block
•
Flue divider
•
Control valve saw
•
Valve plate
•
Gearbox
•
Extension cylinder
•
Saw cylinder
www.forsmw.com
10
NIAB 5 – 15 C
•
Clamp sylinder with sensor
•
Cylinders
•
Cooler
•
Display box & cables
•
List of hoses
Terms
www.forsmw.com
11
NIAB 5 – 15 C
Boom
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Art. nr.
390075
390076
390077
313107
390079
909160
909140
390080
390081
390082
390083
37910225
390084
906960
907620
907625
907246
390085
930105
Sparepart
Boom
Clamp
Clamp
Clamp cylinder
Bracket
Glide bearing
Glide bearing
Axle bolt
Axle bolt
Axle bolt
Axle bolt
Roller with glide bearing
Slide plate
Plug
Spring pin
Spring pin
Locknut
Bolt
Grease nipple
Clamp cylinder with sensor
www.forsmw.com
Dimension
60x65x40
30x34x30
R1“ DIN 906
6x24 DIN1481
6x40 DIN1481
M20 DIN 985
R1/8“
Pcs.
1
1
1
1
2
2
4
2
2
2
4
4
2
2
2
2
4
6
11
1
12
NIAB 5 – 15 C
Boom
www.forsmw.com
13
NIAB 5 – 15 C
Turning bracket (920295)
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Art. nr.
920295
3131331
313133
390090
390091
390092
390093
390094
390095
390096
911290
908245
911260
907630
907246
908450
390097
390098
930105
Sparepart
Turning bracket
Tilt cylinder
Turning cylinder
Axle bolt
Syl. cover
Axle bolt
Axle bolt
Axle bolt
Axle bolt
Safety ring
Lockring
Washer
Lock ring
Spring pin
Locknut
Washer
Glide plastic
Bolt
Grease nipple
Dimension
SGA 170
200x170x3,5
SGA 30
10x45 DIN1481
M20 DIN985
70x25x8
R1/8“
www.forsmw.com
Pcs.
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
3
5
14
NIAB 5 – 15 C
Turning bracket (920295)
www.forsmw.com
15
NIAB 5 – 15 C
Winch part 1
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Art. nr.
390105
390106
390107
930105
906201
908230
910215
910220
390108
390109
390110
390111
906213
908229
906210
907228
909160
909129
906210
908450
906238
920245
390112
390113
390114
390115
Sparepart
Winch sassy
Winch barrel
End cover
Grease nipple
Bolt
Washer
Bearing
Bearing
Washer
Rope arm
Distance ring
Distance ring
Bolt
Washer
Bolt
Locknut
Glide bearing
Glide bearing
Bolt
Washer
Bolt
Wire
Wire brakett
Hook
Couple
Wire end
Dimension
R1/8“
M12x40 DIN931
TBRB 13x24x4
22206CC
6211-2RS1
M12x80 DIN931
13 DIN125
M12x60 DIN931
M12 DIN985
60x65x40
12x18x12
M12x60 DIN931
70x25x8
M20x30 DIN931
Ø8, L=4 m
www.forsmw.com
Pcs.
1
1
1
2
4
3
1
1
1
2
2
1
1
5
1
7
2
2
1
1
1
1
1
3
1
1
16
NIAB 5 – 15 C
Winch part 1
www.forsmw.com
17
NIAB 5 – 15 C
Winch part 2
Pos. nr.
19
20
22
23
24
25
26
27
28
29
30
31
Art. nr.
Sparepart
Socket head cap screw
MC6S 8x35
Washer TBRB 8,4x16
Tredo sealing R1/2”
Hydraulic motor
Sequence valve
Valve block
Adapter
Adapter
Angle adapter
Adapter
Line pip
Angle adapter
www.forsmw.com
Dimension Pcs.
7
7
1
1
1
1
1
1
2
1
1
1
18
NIAB 5 – 15 C
Joystic carrier
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Art. nr.
390210
390211
390212
390213
390215
920255
390216
390217
906222
908267
908240
908260
907215
Sparepart
Joystick carrier
Joystick rod
Handle bracket
Handle
Handle with switch
Stay
Spring
Shaft
Shaft
Bolt
Washer
Washer
Washer
Nut
Dimension
10x13x38
M16x30 DIN 933
17 DIN125
TBRB 10,5x28x6
10,5 DIN125
M10 DIN 934
www.forsmw.com
Pcs.
1
5
5
3
2
2
1
1
1
2
2
2
2
2
19
NIAB 5 – 15 C
15
16
17
18
19
20
21
22
23
907216
390218
907237
906204
908230
907228
909132
906163
907213
Nut
Bolt
Locknut
Bolt
Washer
Locknut
Plastic bush
Bolt
Locknut
M10 DIN1857
M16 DIN 985
M12x45 DIN 931
TBRB 13x24x4
M12 DIN 985
20x23x30x15
M8x30 DIN 933
M8 DIN985
2
2
2
2
4
2
12
12
12
Joystick carrier
www.forsmw.com
20
NIAB 5 – 15 C
Lenght meter (3900910)
www.forsmw.com
21
NIAB 5 – 15 C
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Art. nr.
390260
911137
390261
390262
390263
910217
911272
911125
390264
906508
906248
909142
390265
908270
907246
390266
909127
906182
907219
907215
906529
390267
390268
390269
906530
390270
930105
390271
Sparepart
Wheel
Lock ring
Plug (plastic)
Bracket
Holder
Bearing
Lockring
Lockring
Slit roller
Bolt
Bolt
Bronze bush
Distance
Washer
Locknut
Cylinder
Bronze bush
Bolt
Locknut
Nut
Bolt
Pin bolt
Nut
Taper
Bolt
O-ring
Grease nipple
Clamp
Dimension
SGH 95
R1“
6012-2RS
SGA 60
SGH 52
M3x8 DIN 912
M20x100 DIN 931
30x34x45x20
21 DIN125
DIN985 M20
10x12x15
M10x50 DIN 931
M10 DIN 985
M10 DIN 934
M10x75 DIN 912
M10x90 DIN912
27x3
R1/8“
Pcs.
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
Lenght meter (3900910)
www.forsmw.com
22
NIAB 5 – 15 C
Boom & delimbing arm
www.forsmw.com
23
NIAB 5 – 15 C
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Art. nr.
390075
390060
390240
390225
390226
390382
908110
390228
390229
920510
390230
907610
390231
390232
907213
908220
914615
914610
906512
906169
390233
906150
390234
914716
914718
914720
914582
914584
Sparepart
Boom
Delimbing arm
Extension cylinder
Guide rail
Tubing
Termoplast hose
Spring pin
Roller
Tube
Spring
Axle bolt
Spring pin
Plastic bush
Bolt
Locknut
Washer
T-adapter
Angle adapter
Bolt
Bolt
Plate
Bolt
O-ring
Adapter
Adapter
Adapter
Rubber steel ring
Rubber steel ring
Dimension
Hose nr. 24
4x45 DIN 94
12x16x66
7x10x45
5x30
M8 DIN 985
8,4 DIN 125
M6x20 DIN 7991
M10x14 DIN 933
M8x12 DIN 933
15x2,5
R3/8“
R1/2“
Pcs.
1
1
1
1
1
2
3
2
1
1
1
2
4
2
2
2
2
1
1
1
1
1
2
2
1
3
1
Boom & delimbing arm
www.forsmw.com
24
NIAB 5 – 15 C
DELIMBING ARM (390060)
www.forsmw.com
25
NIAB 5 – 15 C
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
Art. nr.
390060
390061
313108
909140
390063
390064
906173
390065
390066
930105
390067
Sparepart
Delimbing arm
Delimbing knife
Delimbing cylinder
Glide bearing
Axle bolt
Closing plate
Bolt
Axle bolt
Axle bolt
Grease nipple
Bolt
Dimension
30x34x30
M10x25 DIN933
R1/8“
Pcs.
1
2
2
4
2
1
2
2
2
6
6
Tank (390280)
www.forsmw.com
26
NIAB 5 – 15 C
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Art. nr.
390280
390281
390282
390283
390284
390285
390286
390287
390288
390289
390290
390291
914798
914728
914590
906173
908620
906160
390292
390293
Sparepart
Tank
Oil filling plug
Oil temp. indicator
Gasket
Element housing
Housing flange gasket
Port body
Filter element
By-pass valve
Cover gasket
Housing cover
Plug
Plug
Adapter
Rubber steel ring
Bolt
Washer
Bolt
Bolt
Plastic washer
Dimension
1 1/4“
1“
M10x25 DIN 933
M10 DIN127B
M8x25 DIN 933
Pcs.
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
4
4
6
2
2
Tank (390280)
www.forsmw.com
27
NIAB 5 – 15 C
Saw
www.forsmw.com
28
NIAB 5 – 15 C
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
Art. nr.
390175
390195
920302
390177
390178
390179
390180
390181
390182
920304
390184
911270
390185
911255
905122
390186
390187
390188
390189
909130
907225
907520
390190
906516
906142
908218
914710
914580
906514
930105
907614
907540
907210
907219
920300
Sparepart
Boom
Saw cylinder
Sword
Saw motor
Saw bracket
Plastic bush
Washer
Washer
Driver
Drive sprocket
Plate
Lock ring
Washer
Lockring
Screw
Washer
Shaft
Pin bolt
Distance
Bronze bush
Nut
Screw
Chain tensioner
Bolt
Screw
Washer
Adapter
Rubber steel ring
Bolt
Grease nipple
Spring pin
Locknut
Locknut
Locknut
Saw chain
Dimension
75x60x0,5
75x60x1
SGA 58
35x25x1
SGA 25
M4x20 DIN 916
16x4,3x1
M12x45
20x23x15
M12 DIN 6926
M10x50 DIN 916
M8x22 DIN 912
M6x70 DIN84
6,4 DIN125
R1/4“
M6x25 DIN 7991
R1/8“
6x14 DIN 1481
M4 DIN 985
M6 DIN 985
M10 DIN 985
Pcs.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
4
1
4
1
4
2
1
Saw
www.forsmw.com
29
NIAB 5 – 15 C
Valve block (390155)
www.forsmw.com
30
NIAB 5 – 15 C
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Art. nr.
390155
390156
390157
390158
390159
390160
390161
390162
390163
390164
390165
390166
390167
914710
914726
914712
390168
390169
914660
390170
914716
914810
390171
914720
914584
914582
914580
914586
914578
Sparepart
Valve block
Check valve
Pressure reducing valve
Needle valve free reverse
Tree way valve
Differential sensing valve
Electric valve
Coil 12V
Ball
Spring
Spacer
Ball
Spring
Adapter
Adapter
Adapter
Check valve
Adapter
Pressure gauge connection
Pin bolt
Adapter
O-ring
Adapter
Adapter
Rubber steel ring
Rubber steel ring
Rubber steel ring
Rubber steel ring
Rubber steel ring
Dimension
RB5
0,25x2,5x15
1/4“
RB10
2x7x30
1/4"
M8x30
8x2
R1/2“
R3/8“
R1/4“
R3/4“
R1/8“
Pcs.
1
2
1
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
2
4
1
1
8
8
5
4
1
1
Valve block (390155)
www.forsmw.com
31
NIAB 5 – 15 C
Flue divider
www.forsmw.com
32
NIAB 5 – 15 C
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Art. nr.
390135
390136
390137
390138
390139
914714
914718
914720
914744
914790
390140
390141
390142
390143
390144
914660
390145
390146
Sparepart
Valve chest
Safety valve
Joystick fastening
Joystick fastening compl.
Spring housing
Adapter
Adapter
Adapter
Adapter
Adapter
Pressure control valve
Adapter
Adapter
Adapter
Banjo screw
Banjo adapter
Angle adapter
Outlet adapter
Inlet adapter
Banjo adapter
Adapter
Pressure gauge connection
T- pipe
Pressure control valve
Joint
Pin bolt
Switcher. (not automatic)
Dimension
1/4"
Pcs.
1
1
5
5
5
2
4
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
5
5
1
Flue divider
www.forsmw.com
33
NIAB 5 – 15 C
Control valve for saw
www.forsmw.com
34
NIAB 5 – 15 C
Pos. nr.
1
2
3
4
5
6
7
Art. nr.
Sparepart
Valve block
Pressure reducing valve
Direction valve
Magnetite
Adapter
Rubber sealing R1/4”
Angle adapter
Dimension
Pcs.
1
1
1
2
5
5
1
Valve block
www.forsmw.com
35
NIAB 5 – 15 C
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
Art. nr.
Sparepart
Valve block
Direction valve
Magnetite
4-way valve el. steered
Magnetite
Pressure reducing valve
Angle adapter
Adapter
Adapter
Screw MC6S 6x40
Pin bolt MSK6SS 10x50
O-ring 12,7x1,78
Dimension
Pcs.
1
1
2
1
1
1
1
3
3
4
2
4
Valve block
www.forsmw.com
36
NIAB 5 – 15 C
www.forsmw.com
37
NIAB 5 – 15 C
Gearbox (390300)
Pos. nr.
1
2
3
4
5
6
6a
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Art. nr.
390300
390301
390302
390303
906528
390304
914820
906530
914568
390305
390306
906517
390307
390308
390309
906192
908625
390310
390311
390312
390313
390314
390315
390316
390317
390318
390319
390320
390321
390322
Sparepart
Gearbox
Pump
Splinted coupling
Bracket
Bolt
Suction connection
O-ring
Bolt
Clip
Suction hose
Pressure connection
Bolt
Pressure hose
Breathing filter
Fastening
Bolt
Washer
Shaft long
Shaft short
Locking device
Gearbox body
Gearbox body
Gear wheel
Bearing
Sealing
Shock
Outgoing axle
Bearing
Sealing
Cover
Dimension
M10x35-12,9 DIN 912
29,7x3,5
M10x90-12,9 DIN 912
Hose nr. 58
M8x25 DIN 912
Hose nr. 32
M12x25 DIN 933
M12 DIN 127B
www.forsmw.com
Pcs.
1
1
1
1
4
1
1
3
1
1
1
4
1
1
1
4
4
1
1
1
1
1
1
2
1
1
1
2
1
1
38
NIAB 5 – 15 C
Gearbox (390300)
www.forsmw.com
39
NIAB 5 – 15 C
Extension cylinder
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Art. nr.
390241
390242
390243
390244
390245
390246
390247
390248
390249
390250
390251
390252
390253
390254
390255
Sparepart
Tube assy
Rod
Front bush
Piston
Scrape ring
Lock ring
Sealing
Lockring
Protection ring
O-ring
Sealing
Sealing
Sealing
Locknut
O-ring
www.forsmw.com
Dimension
30
SGA 44
3025
SRH 48
40/45
39,2x3
30-38x6
45/39x9,6
45/34x4
M20 DIN 985
19,2x3
Pcs.
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
40
NIAB 5 – 15 C
Saw cylinder
Pos. nr.
1
2
3
4
5
6
7
8
9
Art. nr.
390196
390197
390198
390199
390200
390201
390202
909130
390203
Sparepart
Front bush
Piston
Rod
Tube assy
Scrape ring
Sealing
Sealing
Bronze bush
O-ring
www.forsmw.com
Dimension
16-22x3/4
16-22x5
30-22,5x3
20x23x15
12x2
Pcs.
1
1
1
1
1
1
1
1
1
41
NIAB 5 – 15 C
Clamp cylinder with sensor
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
20
21
Art. nr.
Sparepart
Cylinder pipe
Rod piston
Piston
Top nut
Stripper
Piston sealing
Back – up ring
O-ring
Sealing
Lock ring
Lock ring
Grease nipple
Steering
Potentiometer
Glide bearing
Connector
Screw
O-Ring
Stop screw
Plug
Cylinder assy
www.forsmw.com
Dimension
25/35x7/10
25/33x6,5
45-50
44,2x3
50/49x4,2
Ø4
AV47
¼” UNF
50x45x5,4
2520
12x2
M6
M8x1
Pcs.
1
1
1
1
1
1
3
2
1
1
1
2
1
1
2
1
5
1
1
1
42
NIAB 5 – 15 C
Cylinders
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Sparepart
Cylinder assy
Piston rod
Tube assy
Front bush
Piston
Scrape ring
Sealing
Bush
Sealing
O-ring
O-ring
Sealing
Sealing
Locking ring
Locking ring
Locking ring
Grease nipple
Spherical plain bearing
Tiltcylinder
3131331
390001
390002
390003
390004
390005
390006
390007
390008
390009
390010
390011
390012
911120
390013
390014
930105
910315
Turning
cylinder
313133
390020
390021
390003
390004
390005
390006
390007
390008
390009
390010
390011
390012
911120
390013
390014
930105
910315
www.forsmw.com
Clamp
cylinder
313107
390025
390026
390027
390028
390029
390030
390031
390032
390033
390034
390035
390036
911115
390037
390038
930105
910310
Delimbing
cylinder
313108
390043
390044
390045
390046
390029
390030
390031
390047
390048
390034
390049
390036
911115
390050
390051
3930105
910310
43
NIAB 5 – 15 C
Cooler
Pos. nr.
1
2
3
4
5
6
7
8
9
10
11
12
Art. nr.
390330
390331
390332
390333
390334
390335
914727
914798
914762
906154
908221
Sparepart
Cooler
Fan
Cover
Thermostat
Rubber amortisator
Relay
Adapter
Rubber steel ring
Adapter
Angle adapter
Bolt
Washer
www.forsmw.com
Dimension
R1“
M8x16 DIN933
8,4 DIN 125
Pcs.
1
1
1
1
4
1
1
1
1
1
8
8
44
NIAB 5 – 15 C
Display box & cables
Pos. nr.
1
2
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Art. nr.
Sparepart
Manoeuvre box compl.
Conduit entry
Circuit breaker
Sockel
Cable
Main cable
Plug contact
Plug socket
Push bar type
Tilting switch
Stop push button
Push bar type
Cable (bar)
Cable
Bushing 7 pol
Screw MLC6S 4x12
Contact 7 pol
Measure card
Display card
Red glass
Screw MSCS-A2 3x10
Washer BRB-A4 3,2-7x,05
Cable
Control contact 4 pol
Control contact 4 pol
Cable automatic
Control contact with diode
lamp
Cable
Cladding
Conduit entry
Inductive gauge
Washer BRB 19-34x3
O-Ring 24x5,5
Washer BRB 8,4-16x1,5
Screw MC6S 8x18
Holder inductive gauge
Holder inductive gauge G 10L
Conduit
Steering card automatic
www.forsmw.com
Dimension
Pcs.
45
NIAB 5 – 15 C
Display box & cables
www.forsmw.com
46
NIAB 5 – 15 C
List of hoses
Hose nr. Art. nr.
7
390370
8
390371
9
390372
10
390373
16
390376
18
390377
19
390378
20
390379
22
390380
23
390381
24
390382
25
390383
26
390384
27
390385
28
390386
29
30
390387
32
390388
34
390389
35
390390
37
390391
38
390392
39
390393
40
390394
46
390398
47
48
390399
49
390400
50
51
52
53
54
55
56
57
390401
58
59
60
61
62
63
64
Location
Valve chest - turning cylinder
Valve chest - tilt cylinder
Valve chest - clamp cylinder +
Valve chest - clamp cylinder Delimbing valve - extension cyl. Saw motor - delimbing valve return
Saw motor - delimbing valve spill
Delimbing valve - saw sylinder
Delimbing valve - extension cyl. out front
Delimbing valve - filter
Termoplast twinhose inside boom
T-adapter - delimbing sylinder rear T-adapter - delimbing sylinder rear +
T-adapter - delimbing sylinder front T-adapter - delimbing sylinder front +
Suction pipe
Delimbing valve -extension cyl. out rear
Pump -valve chest
Valve chest - winch block
Winch block - valve chest return.
Delimbing valve - saw motor
Valve chest - delimbing valve knives
Valve chest - delimbing cylinder knives
Greasing hose
Grease pump - delimbing valve
Drainage
Valve chest - cooler
Cooler - filter
Twigg
P Control valve
A Control valve
B Control valve
Winch -tank
T Control valve for cooler
PR Control valve for measuring cylinder
Valve chest - delimbing valve
Automatic block. KLB+ - control
Automatic block. INC - Twigg
Automatic block. UTC -Twigg
Automatic block. INV - control
Automatic block. UTV - control
Automatic block. KLB - control
T Control valve auto block
www.forsmw.com
Dim.
1/4“
3/8“
1/4“
1/4“
1/2“
1/2“
1/4“
1/4“
1/2“
3/4“
3/8“
3/8“
3/8“
3/8“
3/8“
38,1 spiral
1/2“
3/4“
1/2“
1/2“
1/2“
3/8“
3/8“
1/4“
3/16“
3/16”
3/4“
3/4“
1/4“
1/4“
1/4“
1/4“
1/4“
1/4“
1/4“
1/2“
1/4“
1/2“
1/2“
1/2“
1/2“
1/4“
1/4“
Pcs.
2
2
2
2
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
47
NIAB 5 – 15 C
Flow scheme
www.forsmw.com
48
NIAB 5 – 15 C
El. schema/ electrical circuit
www.forsmw.com
49