EN KT Polfill - Akrylowy podk³ad wype³niajacy 2K HS 4+1x
Transkrypt
EN KT Polfill - Akrylowy podk³ad wype³niajacy 2K HS 4+1x
Technical Data Sheet: TDS- 21/2016 Issue Date: 05-04-2016 Version: 2 Technical Data Sheet POLFILL – ACRYLIC FILLER 2K HS 4 + 1 Product for professional use only Characteristic: High quality two-component primer based on acrylic resins. It has excellent insulating and filling properties as well as good adhesion to various surfaces commonly found in passenger cars. It is easy to sanding and fast drying. It can be coated with various topcoats. It is available with “normal” hardener. Surfaces: • • • • • • steel, aluminium, polyester putties, epoxy fillers, wash primers, old paint coatings. Surface preparation: The surface must be dry sanded, cleaned, degreased and dried thoroughly. Filler preparation: Mixing ratio by volume Acrylic filler 4 Hardener 1 Polfill – Thinner for acrylic products 10 – 20% Mix thoroughly filler, hardener and thinner for acrylic products until a uniform consistency is obtained. Observe the required amount of hardener. Spray viscosity: 25-35 s Ford cup 4/20°C LERG SA PustkówOsiedle 59d 39206 Pustków 3 Polska Dział Obsługi Klienta: NIP: 8720003568 Tel: +48 (14) 680 62 85 REGON: 850022800 Fax: +48 (14) 680 63 00 KRS: 0000033727 e-mail: [email protected] www.polfill.com.pl str.1/3 Application: Apply with a spray gun with nozzle diameter 1,5 – 2,2 mm at the air pressure 3 – 3,5 bar. Number of layers: 1 – 3 Coat thickness: 60 – 240 µm Pot life: 1,0 – 2,0 h at 20°C Flash off time between layers: 10 - 15 minutes at 20°C It is recommended to apply the filler at a temperature above 10°C and a relative air humidity of not more than 75%. Drying time: 5 – 8 hours at 20°C 35 – 45 minutes at 60-80°C The temperature below 20°C increases the hardening time. Sanding: Sand dry with P320 – P500. Sand wet with P600 – P1000. Physicochemical properties: This is a grey liquid with an aromatic, sweet odour. The maximum content of VOC for ready to use product is 540 g/l. Storage: Store the product tightly closed in original container, in dry and cool places, away from fire and heat sources at temperatures from 5°C to 20°C. Do not expose to direct sunlight. Shelf life: 12 months from the date of manufacture Health & safety recommendations: Safety Data Sheet and the applicable regulations for health and safety at work involving exposure to chemical factors. LERG SA PustkówOsiedle 59d 39206 Pustków 3 Polska Dział Obsługi Klienta: NIP: 8720003568 Tel: +48 (14) 680 62 85 REGON: 850022800 Fax: +48 (14) 680 63 00 KRS: 0000033727 e-mail: [email protected] www.polfill.com.pl str.2/3 Hardener: Use only Normal 1+4 hardener for acrylic filler 2K HS 4+1. Equipment cleaning: Polfill – NITRO thinner, Polfill – Thinner for acrylic products. The information contained in this sheet has been developed based on our knowledge and practice. However, no individual product properties can be guaranteed under different conditions of use beyond our control. Therefore, we cannot accept full responsibility for the results obtained in specific conditions of use. It is necessary to test the application of the product on a small area first, due to the potential differences in the behaviour of the product depending on the surface treated. Relevant product quality is guaranteed if used according to our instruction of use only. LERG SA PustkówOsiedle 59d 39206 Pustków 3 Polska Dział Obsługi Klienta: NIP: 8720003568 Tel: +48 (14) 680 62 85 REGON: 850022800 Fax: +48 (14) 680 63 00 KRS: 0000033727 e-mail: [email protected] www.polfill.com.pl str.3/3