EN KT Polfill - Akrylowy lakier bezbarwny Superior 2K HS 2 do 1x
Transkrypt
EN KT Polfill - Akrylowy lakier bezbarwny Superior 2K HS 2 do 1x
Technical Data Sheet: TDS- 32/2016 Issue Date: 05-04-2016 Version: 1 Technical Data Sheet POLFILL – ACRYLIC CLEARCOAT SUPERIOR 2K HS 2:1 Product for professional use only Characteristic: This is a high solid acrylic clear coat for car repairs. It is very easy in application, fast drying and high gloss. It can be applied directly over the base layer 15-20 minutes after solvent evaporation. Its hardness, UV resistance and resistance to all climatic conditions ensure a good appearance and stable layer. It is available in two versions: with “standard” hardener or “fast” hardener, depending on the conditions of use. Surfaces: • solvent and waterborne basecoats Clearcoat preparation: Mixing ratio by volume Clearcoat 2 Hardener 1 Polfill – Thinner for acrylic products 5 – 10% Mix thoroughly clearcoat, hardener and thinner for acrylic products until a uniform consistency is obtained. Observe the required amount of hardener. Spray viscosity: without dilution 18 - 19 s DIN 4/20°C after dilution 15 - 16 s DIN 4/20°C Application: Apply with a spray gun with nozzle diameter 1,3 – 1,4 mm at the air pressure 2,0 – 2,5 bar. Number of layers: 1,5 – 2 Pot life: 1 hour at 20°C using Normal hardener Flash of time between layers: 10 - 12 minutes at 20°C It is recommended to apply the clearcoat at a temperature above 10°C and a relative air humidity of not more than 70%. LERG SA PustkówOsiedle 59d 39206 Pustków 3 Polska Dział Obsługi Klienta: NIP: 8720003568 Tel: +48 (14) 680 62 85 REGON: 850022800 Fax: +48 (14) 680 63 00 KRS: 0000033727 e-mail: [email protected] www.polfill.com.pl str.1/2 Drying time: Dust dry: 30 minutes at 20°C Operating hardness: 14 hours at 20°C or 25 minutes at 60°C Full hardness: 4 days The curing times refer to the temperatures of individual object. The temperature below 20°C increase hardening time. Physicochemical properties: This is a colourless liquid with an aromatic, sweet odour. The maximum content of VOC for ready to use product is < 840 g/l. Storage: Store the product tightly closed in original container, in dry and cool places, away from fire and heat sources at temperatures from 5°C to 25°C. Do not expose to direct sunlight. Shelf life: 12 months from the date of manufacture Health & safety recommendations: Safety Data Sheet and the applicable regulations for health and safety at work involving exposure to chemical factors. Hardener: Use only Polfill Normal 1:2 or Polfill Fast 1:2 hardener for acrylic clearcoat Superior. Equipment cleaning: Polfill – NITRO thinner, Polfill – Thinner for acrylic products. The information contained in this sheet has been developed based on our knowledge and practice. However, no individual product properties can be guaranteed under different conditions of use beyond our control. Therefore, we cannot accept full responsibility for the results obtained in specific conditions of use. It is necessary to test the application of the product on a small area first, due to the potential differences in the behaviour of the product depending on the surface treated. Relevant product quality is guaranteed if used according to our instruction of use only. LERG SA PustkówOsiedle 59d 39206 Pustków 3 Polska Dział Obsługi Klienta: NIP: 8720003568 Tel: +48 (14) 680 62 85 REGON: 850022800 Fax: +48 (14) 680 63 00 KRS: 0000033727 e-mail: [email protected] www.polfill.com.pl str.2/2