FTALUR varnish - PPG Polifarb Cieszyn
Transkrypt
FTALUR varnish - PPG Polifarb Cieszyn
Technical data sheet FTALUR varnish PRODUCT FOR INDUSTRIAL APPLICATION 23 listopada 2007 1/2 Lakier ftalowy uretanowany elektroizolacyjny do pokrywania uzwojeń, klasy B Symbol: 5 L packaging 20 L packaging Characteristics: FTALUR varnish is urethane alkyd resin solution in organic solvents, with additives. It dries in ambient temperature. FTALUR varnish should be thinned with a thinner for alkyd electro-insulating varnishes. Recommended use: FTALUR varnish is designed for protective coating the winding of electrical appliances against biological erosion (fungi, bacteria). The varnish can be also used for impregnation of the winding not exposed to heavy centrifugal forces. It can be used for impregnating electrical engines, small transformers, etc. Impregnation: By dip coating, brush or spray application. At least 2-layer application is recommended. The next layer can be applied after at least 20 h /at temp. 20oC/ from the application of the previous layer. The curing time may be shortened by means of drying at 60÷70oC. depending on the application method, the following viscosity is used (at 20oC acc. to Ford cup ∅ 4mm): • brush 70-100s • spray 20-25s • dip coating 25-35s Curing time:: Up to 48 h in the room temperature, the curing period can be shortened by heating in a drier to the temperature 60-70 oC. electro-insulation - 211492 - 232340 PPG Polifarb Cieszyn SA; ul. Chemików 16; 43-400 Cieszyn; Poland Tel. (+48) 33 85-17-415; fax. (+48) 33 85-17-150; www.sigmaelectro.com.pl Technical data sheet FTALUR varnish PRODUCT FOR INDUSTRIAL APPLICATION 23 listopada 2007 2/2 Detailed parameters: Temperature Indicator TI Density at 20oC Viscosity (Ford cup ∅ 4 mm, 20oC) Solid contents (120 ± 20C, 18 h ) Flash point min.130 [s] 80-120 [%] min.44 [oC] min.23 [hours] max.4 Curing time to 3° at 20oC Coating flexibility No cracking after the bending test on a ∅ 2mm pin • at 20oC No cracking after the bending test on a ∅ 5mm pin • after 24 h at 150oC resistant Resistance to transformer oil - 24 h [kV/mm] Dielectric resistance min.60 • at 20oC min.40 • at 130oC min.40 • after 24 h in water min.25 • after 120 h in water [%] Absorbability in water 24 h 2 co najmniej 0,25 Przechowywanie: Lakier FTALUR należy przechowywać w szczelnie zamkniętych opakowaniach i składować w krytych, przewiewnych magazynach o sprawnie działającej wentylacji, w temperaturze 5-35oC. Okres gwarancji: 6 miesięcy od daty produkcji przy spełnieniu powyższych wymagań w zakresie warunków przechowywania.Występujący w tym okresie wzrost lepkości powinien ustąpić po dodaniu 5% rozpuszczalnika do lakierów ftalowych elektroizolacyjnych o symbolu: 233847. Informacje BHP: Pomieszczenia, w których znajduje się lakier powinny być wentylowane. Należy unikać kontaktu wyrobu ze skórą. W przypadku kontaktu ze skórą zmyć ją wodą z mydłem. W razie dostania się lakieru do oczu należy natychmiast spłukać je dużą ilością wody i skontaktować się z lekarzem. Zaleca się stosowanie okularów i odzieży ochronnej. The data provided here has been based on our present best knowledge, and should be treated as primary, preliminary guidelines and information on the product. Each use should be verified according to the production specification of the user. The quality of our product is guaranteed in conformity with the general sales conditions. electro-insulation PPG Polifarb Cieszyn SA; ul. Chemików 16; 43-400 Cieszyn; Poland Tel. (+48) 33 85-17-415; fax. (+48) 33 85-17-150; www.sigmaelectro.com.pl